Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Removal

REMOVAL

PROCEDURE

1. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

Click here 2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

2. RECOVER REFRIGERANT FROM REFRIGERATION SYSTEM

Click here 3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 4. REMOVE FAN AND GENERATOR V BELT (for 2TR-FE)

4. REMOVE FAN AND GENERATOR V BELT (for 2TR-FE)

Click here 5. REMOVE GENERATOR ASSEMBLY (for 2GR-FKS)

5. REMOVE GENERATOR ASSEMBLY (for 2GR-FKS)

Click here 6. REMOVE FRONT UPPER FENDER APRON SEAL

6. REMOVE FRONT UPPER FENDER APRON SEAL

(a) Using a clip remover, disengage the 5 clips to remove the front upper fender apron seal.

7. DISCONNECT SUCTION HOSE SUB-ASSEMBLY (for 2TR-FE)

(a) Remove the bolt A.

(a) Remove the bolt A.

(b) Remove the bolt B to disconnect the suction hose sub-assembly.

(c) Remove the O-ring from the suction hose sub-assembly.

NOTICE:

Seal the opening of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.

8. DISCONNECT SUCTION HOSE SUB-ASSEMBLY (for 2GR-FKS)

(a) Remove the bolt A.

(a) Remove the bolt A.

(b) Remove the bolt A to disconnect the suction hose sub-assembly.

(c) Remove the O-ring from the suction hose sub-assembly.

NOTICE:

Seal the opening of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.

9. DISCONNECT DISCHARGE HOSE SUB-ASSEMBLY

(a) Remove the bolt to disconnect the discharge hose sub-assembly.

(a) Remove the bolt to disconnect the discharge hose sub-assembly.

(b) Remove the O-ring from the discharge hose sub-assembly.

NOTICE:

Seal the opening of the disconnected parts using vinyl tape to prevent moisture and foreign matter from entering.

10. REMOVE COOLER COMPRESSOR ASSEMBLY (for 2TR-FE)

(a) Disconnect the connector.

(b) Remove the 2 bolts and 2 nuts.

(c) Using an E8 ''TORX'' socket wrench, remove the 2 stud bolts and cooler compressor assembly.

11. REMOVE COOLER COMPRESSOR ASSEMBLY (for 2GR-FKS)

(a) Disconnect the connector.

(b) Remove the 2 bolts and 2 nuts.

(c) Using an E8 ''TORX'' socket wrench, remove the 2 stud bolts and cooler compressor assembly.

Components
COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION *1 COMPRESSOR PICK UP SENSOR *2 MAGNET CLUTCH ASSEMBLY *3 PRESSURE R ...

Disassembly
DISASSEMBLY PROCEDURE 1. REMOVE PRESSURE RELIEF VALVE (a) Remove the pressure relief valve and O-ring. 2. REMOVE MAGNET CLUTCH ASSEMBLY (a) Secure the cooler compressor assembly in a vise bet ...

Other materials:

Sliding Roof Switch Assembly
Components COMPONENTS ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL SLIDING ROOF SWITCH ASSEMBLY (ROOF CONSOLE BOX ASSEMBLY) (a) Connect the connector. (b) Engage the 4 clips to install the sliding roof switch assembly (roof console box assembly). Removal REMOVAL P ...

Removal
REMOVAL CAUTION / NOTICE / HINT CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page ). If the side airbag was deployed, replace the front seat assembly with a ne ...

Touch Panel Switch does not Function
PROCEDURE 1. CHECK MULTI-DISPLAY (a) Check if there is any foreign matter caught between the display and exterior frame of the multi-display. OK: No foreign matter is caught between the display and exterior frame of the multi-display. HINT: If there is foreig ...

В© 2011-2024 Copyright www.ttguide.net