Toyota Tacoma (2015-2018) Service Manual: Remote Control System does not Operate

Toyota Tacoma (2015-2018) Service Manual / Sliding Roof / Sliding Roof System / Remote Control System does not Operate

DESCRIPTION

The main body ECU (multiplex network body ECU) receives remote control signals from the driver door key cylinder or wireless transmitter. Then, the main body ECU (multiplex network body ECU) sends the remote control signals to the sliding roof ECU (sliding roof drive gear sub-assembly) via LIN communication. The sliding roof ECU (sliding roof drive gear sub-assembly) receives those signals and activates the sliding roof motor.

CAUTION / NOTICE / HINT

NOTICE:

The sliding roof key-linked function and sliding roof wireless transmitter-linked function can be customized. Make sure that both functions are ON (See page ).
When the sliding roof ECU (sliding roof drive gear sub-assembly) is removed and reinstalled or replaced, the sliding roof ECU (sliding roof drive gear sub-assembly) must be initialized (See page ).
Since the sliding roof system has functions that use LIN communication, first confirm that there is no malfunction in the LIN communication system with the How to Proceed with Troubleshooting procedure (See page ).
When sliding roof ECU (sliding roof drive gear sub-assembly) DTC is output, first perform troubleshooting for the sliding roof ECU (sliding roof drive gear sub-assembly) DTC.

PROCEDURE

1.	CHECK REMOTE CONTROL FUNCTION

(a) Check the key-linked and wireless transmitter-linked function (See page ).

Result	Proceed to
The roof glass does not operate by the key-linked or wireless transmitter-linked function,	A
The roof glass operates by both the key-linked and wireless transmitter-linked function.	B

USE SIMULATION METHOD TO CHECK

2.	CHECK SLIDING ROOF OPERATION

(a) Check the sliding roof operation (See page OK: ).

OK:

Sliding roof operation operates normally.

GO TO OTHER PROBLEM (Sliding Roof does not Move by Operating Sliding Roof Control)

3.	REPLACE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

(a) Replace the sliding roof ECU (sliding roof drive gear sub-assembly) (See page ).

4.	INITIALIZE SLIDING ROOF ECU (SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY)

(a) Initialize the sliding roof ECU (sliding roof drive gear sub-assembly) (See page ).

5.	CHECK REMOTE CONTROL FUNCTION

(a) Check the key-linked and wireless transmitter-linked function (See page OK: ).

OK:

The key-linked and wireless transmitter-linked function operates normally.

END (SLIDING ROOF ECU WAS DEFECTIVE)

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

Sensor (Motor) Failure (B2341,B2344)

DESCRIPTION When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored. When the sliding roof ECU ( ...

Sliding Roof does not Move by Operating Sliding Roof Control Switch

DESCRIPTION The sliding roof ECU (sliding roof drive gear sub-assembly) receives slide and tilt signals when the sliding roof switch is operated and drives its built-in motor. WIRING DIAGRAM CA ...

Other materials:

AUTO LSD Indicator Light Remains ON
DESCRIPTION During normal mode, pressing the VSC OFF switch for a short amount of time changes vehicle to AUTO LSD mode. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: When replacing the brake actuator assembly, perform calibration (See page ). PROCEDURE 1. CHECK ...

Key information
The following keys are provided with the vehicle. Vehicles without engine immobilizer system Master keys Key number plate Vehicles with engine immobilizer system Master keys Key number plate ■Key number plate Keep the plate in a safe place such as your wallet, not in the v ...

Fog Light Relay
Inspection INSPECTION PROCEDURE 1. INSPECT FOG LIGHT RELAY (a) Check the resistance. (1) Using an ohmmeter, measure the resistance between the terminals. Standard: Tester Connection Specified Condition 3-5 10 kΩ or higher ...