REASSEMBLY
PROCEDURE
1. INSTALL INSTRUMENT PANEL CUSHION
(a) Install a new instrument panel cushion as shown in the illustration. Text in Illustration
HINT:
|
|
2. INSTALL NO. 4 INSTRUMENT PANEL CUSHION
(a) Install a new No. 4 instrument panel cushion as shown in the illustration. Text in Illustration
HINT:
|
|
3. INSTALL NO. 2 INSTRUMENT PANEL CUSHION
(a) Align a new No. 2 instrument panel cushion with the silencer markings on the instrument panel sub-assembly and install the No. 2 instrument panel cushion using hot-melt glue. Text in Illustration
|
|
4. INSTALL NO. 1 INSTRUMENT PANEL CUSHION
(a) Align a new No. 1 instrument panel cushion with the silencer markings on the instrument panel sub-assembly and install the No. 1 instrument panel cushion using hot-melt glue. Text in Illustration
|
|
5. INSTALL NO. 1 METER HOOD RETAINER
HINT:
Use the same procedure as for the opposite side.
(a) Engage the guide to install the No. 1 meter hood retainer. |
|
(b) Install the screw <D>.
6. INSTALL NO. 1 INSTRUMENT PANEL PIN
HINT:
Use the same procedure as for the opposite side.
(a) Engage the guide to install the No. 1 instrument panel pin. |
|
(b) Install the screw <F>.
7. INSTALL INSTRUMENT PANEL PASSENGER WITHOUT DOOR AIRBAG ASSEMBLY
8. INSTALL ANTENNA CORD SUB-ASSEMBLY
9. INSTALL NAVIGATION ANTENNA ASSEMBLY (w/ Navigation System)
10. INSTALL NETWORK GATEWAY ECU
11. INSTALL NO. 1 INSTRUMENT PANEL REGISTER SUB-ASSEMBLY
(a) Engage the 3 guides and 6 claws to install the No. 1 instrument panel register sub-assembly. |
|
12. INSTALL DEFROSTER NOZZLE ASSEMBLY
(a) Engage the 3 guides to install the defroster nozzle assembly. |
|
(b) Install the 3 screws <F>.
13. INSTALL SIDE NO. 2 DEFROSTER NOZZLE DUCT
(a) Engage the 2 claws and 2 guides to install the No. 2 defroster nozzle duct. |
|
(b) Install the 2 screws <F>.
14. INSTALL SIDE NO. 1 DEFROSTER NOZZLE DUCT
(a) Engage the 2 claws and 2 guides to install the No. 1 defroster nozzle duct. |
|
(b) Install the 2 screws <F>.
15. INSTALL NO. 2 HEATER TO REGISTER DUCT
(a) Engage the 2 guides to install the No. 2 heater to register duct. |
|
(b) Install the 2 screws <F> and screw <D>.
16. INSTALL NO. 3 HEATER TO REGISTER DUCT
(a) Engage the 2 guides to install the No. 3 heater to register duct. |
|
(b) Install the 2 screws <F> and screw <D>.
17. INSTALL NO. 1 HEATER TO REGISTER DUCT
(a) Engage the 2 guides to install the No. 1 heater to register duct. |
|
(b) Install the 2 screws <F> and screw <D>.
Pressure Control Solenoid "G" Electrical (Shift Solenoid Valve SL4) (P2810)
DESCRIPTION
Changing from 1st to 6th is performed by the ECM turning shift solenoid valves
SL1, SL2, SL3 and SL4 on and off. If an open or short circuit occurs in any of the
shift solenoid valves, the ECM controls the remaining normal shift solenoid valves
to allow the vehicle to be operated ...
Components
COMPONENTS
ILLUSTRATION
*A
for Driver Side
-
-
*1
FRONT SEAT CUSHION HEATER ASSEMBLY
*2
SEPARATE TYPE FRONT SEAT CUSHION COVER
*3
TAG PIN
-
-
...
Stereo Component Amplifier Power Source Circuit
DESCRIPTION
This circuit provides power to the stereo component amplifier assembly.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
Inspect the fuses for circuits related to this system before performing the following
inspection procedure.
PROCEDURE
1.
CHECK HARNESS AND CONNE ...