Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Reassembly

REASSEMBLY

PROCEDURE

1. INSTALL UN-LOCK WARNING SWITCH ASSEMBLY (w/o Smart Key System)

(a) Engage the 2 claws to install the un-lock warning switch assembly to the upper steering column bracket assembly.

2. INSTALL IGNITION SWITCH LOCK CYLINDER ASSEMBLY (w/o Smart Key System)

(a) Turn the ignition switch to ACC.

(b) Install the ignition switch lock cylinder assembly to the upper steering column bracket assembly.

(c) Make sure that the ignition switch lock cylinder assembly is securely installed into the upper steering column bracket assembly.

3. INSTALL KEY INTER LOCK SOLENOID (for Automatic Transmission without Smart Key System)

(a) Engage the claw to install the key interlock solenoid to the upper steering column bracket assembly.

(b) Install the screw.

4. INSTALL IGNITION OR STARTER SWITCH ASSEMBLY (w/o Smart Key System)

(a) Install the ignition or starter switch assembly to the upper steering column bracket assembly with the 2 screws.

5. INSTALL TRANSPONDER KEY AMPLIFIER (w/o Smart Key System)

(a) Engage the 2 claws to install the transponder key amplifier.

6. INSPECT STEERING LOCK OPERATION (w/o Smart Key System)

(a) Check that the steering mechanism is activated when removing the key.

(b) Check that the steering mechanism is deactivated when inserting the key and turning it to ACC position.

7. INSTALL UPPER STEERING COLUMN BRACKET WITH SWITCH ASSEMBLY (w/o Smart Key System)

(a) Secure the steering column assembly in a vise between aluminum plates.

NOTICE:

Do not overtighten the vise.

(b) Temporarily install the upper steering column bracket with switch assembly with a new tapered-head bolt.

(c) Tighten the tapered-head bolt until the bolt head breaks off.

8. INSTALL STEERING LOCK ACTUATOR ASSEMBLY (w/ Smart Key System)

HINT:

  • Perform the same procedure as for the upper steering column bracket with switch assembly.
  • When replacing the steering lock actuator assembly, perform initialization (See page ).

9. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY

(a) Align the matchmarks on the steering intermediate shaft assembly and steering

(a) Align the matchmarks on the steering intermediate shaft assembly and steering main shaft assembly.

(b) Install the steering intermediate shaft sub-assembly with the bolt.

Torque:

35 N·m {357 kgf·cm, 26 ft·lbf}

Installation
INSTALLATION PROCEDURE 1. INSTALL STEERING COLUMN ASSEMBLY (a) Install the steering column assembly with the 2 nuts and bolt. Torque: 21 N·m {214 kgf·cm, 15 ft·lbf} (b) Connect each of the c ...

Steering Lock System
...

Other materials:

Removal
REMOVAL PROCEDURE 1. REMOVE REAR SEAT CUSHION ASSEMBLY (a) Remove the 2 bolts and rear seat cushion assembly. 2. REMOVE REAR SEATBACK HINGE COVER (a) for LH Side: (1) Disengage the 6 claws to remove the 2 rear seatback hinge cov ...

Installation
INSTALLATION PROCEDURE 1. INSTALL VANE PUMP (a) Install the vane pump assembly with the 2 bolts. Torque: 21 N·m {214 kgf·cm, 15 ft·lbf} (b) Connect the oil pressure switch connector. NOTICE: Make sure that no oil adheres to the connector. ...

Pressure Control Solenoid "B" Circuit Open (P077513)
DESCRIPTION Changing from 1st to 6th is performed by the ECM turning shift solenoid valves SL1, SL2, SL3 and SL4 on and off. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated ...

© 2011-2022 Copyright www.ttguide.net