Components
COMPONENTS
ILLUSTRATION
Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE BUSH
(a) Fix the spring in a vise.
(b) Using a hack saw, cut both ends off the bushes.
(c) Using SST and a press, press out the 2 bushes. SST: 09950-60010 09951-00350 SST: 09950-70010 09951-07100 |
|
(d) Using a chisel and hammer, tap out the 2 outer tubes. |
|
Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL BUSH
(a) Using SST and a press, press in 2 new bushes.
SST: 09710-28012
09710-07062
SST: 09710-30041
09710-03211
Removal
REMOVAL
PROCEDURE
1. REMOVE REAR WHEEL
2. REMOVE SPARE TIRE
3. SEPARATE REAR SHOCK ABSORBER
(a) Support the rear axle housing. |
|
(b) Remove the bolt, nut and washer.
(c) Separate the shock absorber from the rear axle housing.
4. SEPARATE PARKING BRAKE CABLE ASSEMBLY NO. 3
(a) Remove the bolt, then separate the parking brake cable.
5. REMOVE REAR SPRING U BOLT
(a) Remove the 4 nuts and 4 washers.
(b) Remove the spring seat and 2 U-bolts.
(c) Remove the spring bumper.
6. REMOVE REAR LEAF SPRING
(a) Remove the nut, washer and through bolt.
(b) Remove the nut, washer and through bolt. NOTICE: Be careful not to drop the spring when removing the through bolt. |
|
(c) Remove the spring.
7. REMOVE REAR SPRING SHACKLE SUB-ASSEMBLY NO. 2
(a) Remove the nut, washer, through bolt and shackle.
Installation
INSTALLATION
PROCEDURE
1. INSTALL REAR SPRING SHACKLE SUB-ASSEMBLY NO. 2
(a) Install the shackle with the through bolt, washer and nut.
2. INSTALL REAR LEAF SPRING
(a) Place the spring in the rear axle housing.
(b) Align the hole of the rear axle housing with the head of the spring center bolt.
(c) Install the through bolt, washer and nut. |
|
(d) Install the through bolt, washer and nut. |
|
3. INSTALL REAR SPRING U BOLT
(a) Install the spring bumper.
(b) Install the spring seat, 2 U-bolts, 4 washers and 4 nuts. Torque: 70 N·m {714 kgf·cm, 52 ft·lbf} HINT: Tighten the U-bolts until the lengths of all the U-bolts under the spring seat are the same. |
|
4. INSTALL PARKING BRAKE CABLE ASSEMBLY NO. 3
(a) Install the parking brake cable with the bolt.
Torque:
13 N·m {127 kgf·cm, 9 ft·lbf}
5. INSTALL REAR SHOCK ABSORBER
(a) Install the shock absorber with the bolt, nut and washer.
6. INSTALL REAR WHEEL
Torque:
113 N·m {1152 kgf·cm, 83 ft·lbf}
7. STABILIZE REAR SUSPENSION
(a) Lower the vehicle.
(b) Bounce the vehicle up and down several times to stabilize the suspension.
8. FULLY TIGHTEN REAR SUSPENSION
(a) Tighten the nuts and bolts of the rear suspension parts.
Torque:
Part Tightened |
N*m |
kgf*cm |
ft.*lbf |
---|---|---|---|
Rear LH spring x Rear spring shackle |
120 |
1224 |
89 |
Rear LH spring x Frame |
120 |
1224 |
89 |
Rear spring shackle x Frame |
120 |
1224 |
89 |
Rear shock absorber x Rear axle housing |
58 |
591 |
43 |
9. INSTALL SPARE TIRE
Power Supply Drive Circuit (C1257)
DESCRIPTION
The motor relay (semiconductor relay) is built into the hydraulic brake booster
and drives the pump motor based on a signal from the skid control ECU (master cylinder
solenoid).
DTC No.
DTC Detecting Condition
Trouble Areas
C1257
...
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
Use the table below to help determine the cause of problem symptoms.
If multiple suspected areas are listed, the potential causes of the symptoms
are listed in order of probability in the "Suspected Area" column of the
table. Check each symptom by ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL HYDRAULIC BRAKE BOOSTER
(a) Install a new brake booster gasket onto the hydraulic brake booster.
(b) Install the hydraulic brake booster with the 4 nuts.
Torque:
14 N·m {145 kgf·cm, 10 ft·lbf}
(c) Using a union nut wrench, connect the 4 brake l ...