Toyota Tacoma (2015-2018) Service Manual: Rear Door Black Out Tape
Components
COMPONENTS
ILLUSTRATION
Installation
INSTALLATION
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH and LH sides.
- The procedure described below is for the LH side.
PROCEDURE
1. REPAIR INSTRUCTION
.gif)
2. INSTALL NO. 2 BLACK OUT TAPE
(a) Refer to the illustration to position a new No. 2 black out tape.
Standard Measurement
|
Dimension |
Measurement |
Dimension |
Measurement |
|---|---|---|---|
|
a |
41.8 mm (1.646 in.) |
b |
7.2 to 7.3 mm (0.283 to 0.2874 in.) |
|
c |
3.8 to 4.0 mm (0.150 to 0.157 in.) |
d |
6.0 to 6.2 mm (0.236 to 0.244 in.) 41.8 mm (** in.) |
|
e |
6.7 to 6.9 mm (0.264 to 0.272 in.) |
f |
5.7 to 5.9 mm (0.224 to 0.232 in.) |
|
g |
2.0 mm (0.0787 in.) |
- |
- |
(b) Remove the release paper and apply the No. 2 black out tape.
3. INSTALL REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
(See page
)
Removal
REMOVAL
CAUTION / NOTICE / HINT
HINT:
- Use the same procedure for the RH and LH sides.
- The procedure described below is for the LH side.
PROCEDURE
1. REMOVE REAR DOOR GLASS OUTER WEATHERSTRIP ASSEMBLY
(See page .gif)
)
2. REMOVE NO. 2 BLACK OUT TAPE
(a) Using a heat light, heat the vehicle body and No. 2 black out tape.
Heating Temperature|
Item |
Temperature |
|---|---|
|
Vehicle Body and No. 2 Black Out Tape |
40 to 60°C (104 to 140°F) |
NOTICE:
Do not heat the vehicle body or No. 2 black out tape excessively.
|
(b) Pull back on one of the ends of the No. 2 black out tape to remove it. HINT: When pulling on the No. 2 black out tape, pull it parallel to the body. |
|
Removal
REMOVAL
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for the RH side and LH side.
The following procedure is for the LH side.
PROCEDURE
1. PRECAUTION
NOTICE:
After tur ...
Other materials:
Pressure Control Solenoid "C" Performance (Shift Solenoid Valve SL3) (P0796)
SYSTEM DESCRIPTION
The ECM uses the vehicle speed signal and signals from the transmission revolution
sensors (NT, SP2) to detect the actual gear (1st, 2nd, 3rd, 4th, 5th or 6th gear).
The ECM compares the actual gear with the shift schedule in the ECM memory to
detect mechanical problems of t ...
Dtc Check / Clear
DTC CHECK / CLEAR
1. DTC CHECK USING TECHSTREAM
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Air Conditioner / Trouble Codes.
(e) Check for DTCs.
2. DTC CLEAR USING TECHSTREAM
(a) Conn ...
Inspection
INSPECTION
PROCEDURE
1. INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY
(a) Check the operation of the front seat cushion heater assembly.
(1) Apply battery voltage and check the operation of the front seat cushion
heater assembly.
OK:
Connection
...
