DESCRIPTION
The accumulator pressure sensor is connected to the skid control ECU in the master cylinder solenoid.
DTC No. |
DTC Detecting Condition |
Trouble Areas |
---|---|---|
C1254 |
Accumulator pressure sensor fault (Fluid pressure does not change when it should e.g. pump operates, brake pedal depressed/released). |
|
PROCEDURE
1. |
READ VALUE USING DATA LIST (ACCUMULATOR SENSOR) |
(a) Connect Techstream to the DLC3.
(b) Turn the ignition switch to OFF.
(c) Depress the brake pedal more than 20 times.
(d) Turn the ignition switch to the ON position.
(e) Select the Data List mode on the Techstream.
ABS/VSC/TRAC
Tester Display |
Measurement Item / Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
Accumulator Sensor |
Accumulator pressure sensor reading / min.: 0 V, max.: 5 V |
3.58 to 5 V |
- |
(f) Confirm whether the accumulator output voltage is normal.
Result |
Proceed to |
---|---|
Output value normal |
A |
Output value not normal |
B |
B |
REPLACE MASTER CYLINDER SOLENOID |
|
2. |
READ VALUE USING DATA LIST (MASTER CYLINDER PRESSURE SENSOR) |
(a) Turn the ignition switch to OFF.
(b) Depress the brake pedal more than 20 times.
(c) Install a brake pedal effort gauge (SST), and bleed air.
(d) Connect Techstream to the DLC3.
(e) Turn the ignition switch to the ON position.
(f) Select the Data List mode on the Techstream.
ABS/VSC/TRAC
Tester Display |
Measurement Item / Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
Master Cylinder Sensor |
Master cylinder pressure sensor reading / min.: 0 V, max.: 5 V |
0.3 to 1.9 V With pedal pressure of 49 N (5 kgf, 11 lbf) |
Front brake pressure: 770 to 1280 kPa (7.9 to 13.1 kgf/cm2, 112 to 186 psi) |
(g) Check that the master cylinder output value is in the Normal Condition range.
OK:
Master cylinder pressure sensor value is in the Normal Condition.
NG |
REPLACE MASTER CYLINDER SOLENOID |
|
3. |
RECONFIRM DTC |
(a) Clear the DTCs (See page ).
(b) Turn the ignition switch to OFF.
(c) Depress the brake pedal more than 20 times.
(d) Turn the ignition switch to the ON position.
(e) Wait until the pump motor stops.
(f) Depress the brake pedal and release it.
(g) Wait for 25 minutes.
(h) Check if the same DTCs are recorded.
Result |
Proceed to |
---|---|
DTC output |
A |
DTC not output |
B |
A |
REPLACE MASTER CYLINDER SOLENOID |
B |
END |
Front Passenger Side Door ECU Communication Stop (B2322)
DESCRIPTION
This DTC is stored when LIN communication between the front power window regulator
motor assembly RH and main body ECU (multiplex network body ECU) stops for 10 seconds
or more.
DTC No.
DTC Detection Condition
Trouble Area
B2322
...
Rear Right Center Sensor Malfunction (C1AE8)
DESCRIPTION
The No. 1 ultrasonic sensor (rear center sensor RH) is installed on the rear
bumper. The ECU detects obstacles based on signals received from the No. 1 ultrasonic
sensor (rear center sensor RH). If the No. 1 ultrasonic sensor (rear center sensor
RH) has an open circuit or other ma ...
Clutch Accumulator
Components
COMPONENTS
ILLUSTRATION
Installation
INSTALLATION
PROCEDURE
1. INSTALL CLUTCH ACCUMULATOR ASSEMBLY
(a) Install the clutch accumulator assembly to the manual transmission assembly
with the 3 bolts.
Torque:
12 N·m {120 kgf·cm, 9 ft·lbf}
(b) Using a union nut wrench, co ...