Toyota Tacoma (2015-2018) Service Manual: Precaution
PRECAUTION
IGNITION SWITCH EXPRESSIONS
(a) The type of ignition switch used on this model differs according to the specifications of the vehicle. The expressions listed in the table below are used in this section.
|
Expression |
Ignition Switch (Position) |
Engine Switch (Condition) |
|---|---|---|
|
Ignition Switch off |
LOCK |
Off |
|
Ignition Switch ON |
ON |
On (IG) |
|
Ignition Switch ACC |
ACC |
On (ACC) |
|
Engine Start |
START |
Start |
HANDLING PRECAUTION FOR DYNAMIC RADAR CRUISE CONTROL SYSTEM
Keep in mind the following points when servicing vehicles equipped with the dynamic radar cruise control system.
(a) The dynamic radar cruise control system is designed to be used when driving on highways and freeways. The system may not operate correctly when driving on roads used by pedestrians and bicycles, and may result in an accident.
(b) Do not overly rely on the dynamic radar cruise control system.
- The dynamic radar cruise control system is designed to assist in maintaining an appropriate distance with the preceding vehicle, however, the system alone is not sufficient. Pay constant attention to the vehicle-to-vehicle distance and the traffic conditions when using the dynamic radar cruise control system and decelerate with the brake pedal or accelerate with the accelerator pedal according to the situation to keep an appropriate distance with the preceding vehicle.
- The dynamic radar cruise control system applies brakes as necessary, however, there is a limitation on the deceleration control capability. When the preceding vehicle decelerates rapidly or another vehicle moves in front of the vehicle, decelerating in time to avoid a collision may not be possible without additional braking.
(c) The millimeter wave radar sensor dirt detection function
- The millimeter wave radar sensor can automatically detect dirt on the sensor face or the front or back surface of the front emblem, however, dirt may not always be detected.
- The dirt detection function may not operate if a metal object or plastic sheet with metal coating is attached to the sensor or the front emblem.
- The dirt detection function may not operate if there is snow or ice on the sensor or the front emblem.
HINT:
The preceding conditions may result in the vehicle being unable to maintain an appropriate distance with the preceding vehicle.
(d) Keep the sensor face and the front and back surfaces of the front emblem clean.
(e) The dynamic radar cruise control system does not operate or give a vehicle approach warning for vehicles which are stopped or driving at significantly slower speeds.
HINT:
This includes vehicles stopped at a tollgate or in traffic, or a preceding vehicle driving at significantly slower speeds.
(f) When following another vehicle with vehicle-to-vehicle distance control mode controlling vehicle speed, the vehicle will not accelerate if the cruise control switch is pushed to +/RES as the speed is controlled in accordance with the speed of the preceding vehicle.
NOTICE:
If the set vehicle speed is increased by pushing the cruise control switch to +/RES, the vehicle will accelerate to the newly set speed when the preceding vehicle moves out of the lane.
HINT:
The set vehicle speed can be confirmed on the multi-information display.
(g) The actual vehicle-to-vehicle distance may be shorter than the set vehicle-to-vehicle distance when driving on a downhill road.
(h) When a system malfunction is detected, the master warning light illuminates, a warning message is displayed on the multi-information display in the combination meter assembly and the buzzer sounds.
(i) Keep the windshield glass clean.
(j) Do not apply excessive force to the forward recognition camera or subject it to a strong impact.
(k) Do not disassemble the forward recognition camera.
(l) Do not attach a sticker to the windshield glass in the area in front of the forward recognition camera.
(m) If the heater is used with FOOT mode selected, the upper area of the windshield glass may fog up, affecting the operation of the forward recognition camera.
HINT:
If the windshield glass fogs up, clear it using the front defroster.
(n) Do not damage the forward recognition camera lens or allow it to become dirty.
HINT:
- When cleaning the inner surface of the windshield glass, do not allow cleaning agent to contact the forward recognition camera lens.
- Do not touch the forward recognition camera lens.
(o) Do not place any objects on top of the instrument panel.
HINT:
If an object is reflecting off of the windshield glass, the performance of the forward recognition camera may decrease.
(p) The vehicle approach warning buzzer does not sound when constant speed control mode is controlling vehicle speed because the presence of and distance to the preceding vehicle is not calculated.
(q) As the controls performed by constant speed control mode and vehicle-to-vehicle distance control mode are different, confirm which mode is selected when using the dynamic radar cruise control system.
(r) For other precautions related to constant speed control mode, refer to Precautions for the conventional cruise control system.
Click here .gif)
HANDLING PRECAUTIONS FOR FORWARD RECOGNITION CAMERA
Click here
PRECAUTION WHEN REPLACING ECM
Before replacing the ECM, refer to Registration.
w/o Smart Key System: Click here
w/ Smart Key System: Click here
PRECAUTIONS WHEN REPLACING MILLIMETER WAVE RADAR SENSOR ASSEMBLY
When the millimeter wave radar sensor assembly is replaced with a new one, adjustment of the radar sensor beam axis must be performed.
Click here
PRECAUTION WHEN REPLACING SKID CONTROL ECU (HYDRAULIC BRAKE BOOSTER)
After the skid control ECU (hydraulic brake booster) is replaced, perform the yaw rate sensor and G sensor zero point calibration and store the system information.
Click here
PRECAUTION WHEN REPLACING SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)
After the skid control ECU (brake actuator assembly) is replaced, perform the yaw rate sensor and G sensor zero point calibration and store the system information.
Click here
PRECAUTION WHEN REPLACING COMBINATION METER ASSEMBLY
When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
Definition Of Terms
DEFINITION OF TERMS
Term
Definition
Monitor Description
Description of what the ECM monitors and how it detects malfunctions
(monitoring purpose ...
Other materials:
Transmission Fluid Temperature Sensor "B" Circuit Short to Battery or Open (P274015)
DESCRIPTION
The No. 2 ATF temperature sensor is installed in the transmission valve body
assembly.
If the ECM detects an abnormally high ATF temperature near this sensor, it illuminates
the warning indicator.
HINT:
The temperature of ATF easily rises when towing, climbing hills, in traffic, ...
Runnable Signal Malfunction (B2286,P0335)
DESCRIPTION
These DTCs are stored when the engine speed signal sent by the ECM via direct
line and the engine speed signal sent via CAN communication do not match.
HINT:
When the cable is disconnected and reconnected to the negative (-) battery terminal,
the power source mode returns to the s ...
Pressure Sensor Circuit (B1423)
DESCRIPTION
This DTC is stored if refrigerant pressure on the high pressure side is extremely
low (176 kPa (1.8 kgf/cm2, 26 psi) or less) or extremely high (3140 kPa (32.0 kgf/cm2,
455 psi) or more). The air conditioner pressure sensor, which is installed on the
pipe on the high pressure side ...
