Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Parking Brake Cable

Components

COMPONENTS

ILLUSTRATION

Removal

Removal

REMOVAL

PROCEDURE

1. DISCONNECT NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER

(See page 2. REMOVE VOLTAGE INVERTER ASSEMBLY )

2. REMOVE VOLTAGE INVERTER ASSEMBLY

(See page 3. REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY )

3. REMOVE NO. 2 PARKING BRAKE CABLE ASSEMBLY

(a) Loosen the adjusting nut.

(b) Disengage the 2 claws to remove the parking cable end stopper.

(c) Disconnect the No. 2 parking brake cable assembly from the No. 1 parking brake pull rod.

(d) Disengage the 3 claws of the No. 2 parking brake cable assembly and push the No. 2 parking brake cable assembly outside of vehicle slightly.

(e) Remove the 2 bolts and disconnect the No. 2 parking brake cable assembly from the backing plate.

(f) Remove the 4 bolts and No. 2 parking brake cable assembly.

4. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

4. REMOVE NO. 3 PARKING BRAKE CABLE ASSEMBLY

(a) Loosen the adjusting nut.

(b) Disengage the 2 claws to remove the parking cable end stopper.

(c) Disconnect the No. 3 parking brake cable assembly from the No. 1 parking brake pull rod.

(d) Disengage the 3 claws of the No. 3 parking brake cable assembly and push the No. 3 parking brake cable assembly outside of vehicle slightly.

(e) Remove the 2 bolts and disconnect the No. 3 parking brake cable assembly from the backing plate.

(f) Remove the 4 bolts and No. 3 parking brake cable assembly.

Installation

Installation

INSTALLATION

PROCEDURE

1. INSTALL NO. 3 PARKING BRAKE CABLE ASSEMBLY

(a) Install the No. 3 parking cable assembly with the 4 bolts.

Torque:

13 N·m {127 kgf·cm, 9 ft·lbf}

(b) Attach the claws of the No. 3 parking brake cable assembly.

(c) Connect the No. 3 parking brake cable assembly to the No. 1 parking brake pull rod.

(d) Engage the 2 claws to install the parking brake cable end stopper.

(e) Install the No. 3 parking brake cable assembly to the backing plate with the 2 bolts.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

2. INSTALL NO. 2 PARKING BRAKE CABLE ASSEMBLY

(a) Install the No. 2 parking brake cable assembly with the 4 bolts.

Torque:

13 N·m {127 kgf·cm, 9 ft·lbf}

(b) Attach the claws of the No. 2 parking brake cable assembly.

(c) Connect the No. 2 parking brake cable assembly to the No. 1 parking brake pull rod.

(d) Engage the 2 claws to install the parking brake cable end stopper.

(e) Install the No. 2 parking brake cable assembly to the backing plate with the 2 bolts.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

3. CONNECT NO. 2 PARKING BRAKE SHOE ASSEMBLY WITH PARKING BRAKE SHOE LEVER

(See page 4. INSPECT PARKING BRAKE LEVER TRAVEL )

4. INSPECT PARKING BRAKE LEVER TRAVEL

5. ADJUST PARKING BRAKE LEVER TRAVEL

5. ADJUST PARKING BRAKE LEVER TRAVEL

6. INSTALL VOLTAGE INVERTER ASSEMBLY

6. INSTALL VOLTAGE INVERTER ASSEMBLY

(See page 7. INSTALL REAR WHEEL )

7. INSTALL REAR WHEEL

Torque:

113 N·m {1152 kgf·cm, 83 ft·lbf}

Parking Brake
...

Parking Brake Lever
Components COMPONENTS ILLUSTRATION ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL PARKING BRAKE SWITCH ASSEMBLY 2. INSTALL PARKING BRAKE LEVER SUB-ASSEMBLY (a) Install ...

Other materials:

Open in Rear Floor Electrical Key Oscillator Circuit (B27A6)
DESCRIPTION The certification ECU (smart key ECU assembly) generates a request signal and transmits the signal to the No. 2 indoor electrical key antenna assembly (rear floor). For the No. 2 indoor electrical key antenna assembly (rear floor) to detect when the electrical key transmitter sub- ...

Torque Converter Clutch Pressure Control Solenoid Control Circuit Open (P275613)
DESCRIPTION Refer to the system description for DTC P27567F (See page ). DTC No. DTC Detection Condition Trouble Area SAE P275613 Open or short is detected in shift solenoid valve SLU circuit for 1 second or more while d ...

Transmission Fluid Temperature Sensor "A" Circuit Range/Performance (P071000)
DESCRIPTION The No. 1 ATF temperature sensor converts the fluid temperature into a resistance value for use by the ECM. The ECM applies a voltage to the temperature sensor through terminal THO1 of the ECM. The sensor resistance changes with the ATF temperature. As the temperature becomes hi ...

© 2011-2024 Copyright www.ttguide.net