Toyota Tacoma (2015-2018) Service Manual: P/W Master Switch Communication Stop (B1206)

Toyota Tacoma (2015-2018) Service Manual / Multiplex Communication / Lin Communication System / P/W Master Switch Communication Stop (B1206)

DESCRIPTION

This DTC is stored when LIN communication between the power window regulator master switch assembly and main body ECU (multiplex network body ECU) stops for 10 seconds or more.

DTC No.	DTC Detection Condition	Trouble Area
B1206	No communication between power window regulator master switch assembly and main body ECU (multiplex network body ECU) for 10 seconds or more.	Power window regulator master switch assembly Main body ECU (multiplex network body ECU) Driver side junction block Wire harness or connector

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.
If the main body ECU (multiplex network body ECU) is replaced, refer to Registration (See page )

PROCEDURE

1.	INSPECT DRIVER SIDE JUNCTION BLOCK

(a) Remove the driver side junction block (See page (b) Remove the main body ECU (multiplex network body ECU) from the driver side ).

(b) Remove the main body ECU (multiplex network body ECU) from the driver side junction block.

Standard Resistance:

Tester Connection	Condition	Specified Condition
1D-13 - MB-16 (LIN2)	Always	Below 1 Ω

Text in Illustration

Component without harness connected

(Driver Side Junction Block)

HINT:

This inspection is to check the LIN line in the driver side junction block that connects the wire harness to the built-in main body ECU (multiplex network body ECU).

REPLACE DRIVER SIDE JUNCTION BLOCK

2.	CHECK HARNESS AND CONNECTOR (DRIVER SIDE JUNCTION BLOCK - POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY)

(a) for Double Cab

(1) Disconnect the 1D driver side junction block connector.

(2) Disconnect the P18 power window regulator master switch assembly connector.

(3) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
1D-13 - P18-6 (LIN1)	Always	Below 1 Ω
1D-13 or P18-6 (LIN1) - Body ground	Always	10 kΩ or higher

(b) for Access Cab

(1) Disconnect the 1D driver side junction block connector.

(2) Disconnect the P23 power window regulator master switch assembly connector.

(3) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
1D-13 - P23-17 (LIN1)	Always	Below 1 Ω
1D-13 or P23-17 (LIN1) - Body ground	Always	10 kΩ or higher

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.	CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR MASTER SWITCH - POWER SOURCE CIRCUIT)

(a) for Double Cab

(1) Disconnect the P18 power window regulator master switch assembly connector.

(2) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Condition	Specified Condition
P18-3 (B) - P18-1 (GND)	Always	11 to 14 V

(3) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
P18-1 (GND) - Body ground	Always	Below 1 Ω

(b) for Access Cab

(1) Disconnect the P23 power window regulator master switch assembly connector.

(2) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Condition	Specified Condition
P23-11 (B) - P23-12 (GND)	Always	11 to 14 V

(3) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
P23-12 (GND) - Body ground	Always	Below 1 Ω

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.	REPLACE POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY

(a) Replace the power window regulator master switch assembly.

5.	CHECK DTC OUTPUT

(a) Clear the DTCs (See page (b) Recheck for DTCs. ).

(b) Recheck for DTCs.

OK:

DTC B1206 is not output.

END (POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY WAS DEFECTIVE)

REPLACE MAIN BODY ECU (MULTIPLEX BODY ECU)

LIN Communication Bus Malfunction (B2325)

DESCRIPTION The main body ECU (multiplex network body ECU) monitors communication between all the ECUs connected to the door bus lines. When the main body ECU (multiplex network body ECU) detects ...

Lost Communication with Power Source Control (B278C)

DESCRIPTION DTC No. DTC Detection Condition Trouble Area B278C An internal malfunction occurs in the certification ECU (smart key ECU ...

Other materials:

Accumulator Low Pressure (C1256)
DESCRIPTION The accumulator pressure sensor is connected to the skid control ECU in the master cylinder solenoid. DTC No. DTC Detecting Condition Trouble Areas C1256 Fluid pressure inside the accumulator drops below the specification ...

Precaution
PRECAUTION 1. INITIALIZATION NOTICE: If the ECM is replaced, register the ECU communication ID for Engine Immobiliser System (See page ). Perform Registration (VIN registration) when replacing the ECM (See page ). HINT: The engine learned value cannot be rese ...

Noise Occurs or Sound Skips when Portable Player Plays
CAUTION / NOTICE / HINT HINT: Perform this check with the portable player volume set at an appropriate level. Make sure that there are no obstructions between the portable player and navigation receiver assembly that may block signals, and that the portable player and navig ...