Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Operation Check

OPERATION CHECK

INPUT SIGNAL CHECK

*a

+RES

*b

-SET

*c

ON-OFF

*d

CANCEL

(a) Connect the Techstream to the DLC3.

(b) Check the cruise control main switch using the Data List function of the Techstream (ON-OFF, -SET, +RES and CANCEL).

Click here INSPECT CRUISE CONTROL MAIN SWITCH (ON-OFF BUTTON)

INSPECT CRUISE CONTROL MAIN SWITCH (ON-OFF BUTTON)

(a) Turn the ignition switch to ON.

(b) Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).

*a

ON-OFF

(c) Check that the cruise control indicator (vehicle-to-vehicle distance control mode) in the combination meter assembly illuminates and "RADAR READY" is displayed on the multi-information display.

*1

Cruise Control Indicator

(Vehicle-to-vehicle Distance Control Mode)

*2

Multi-information Display

(d) Turn the cruise control system off using the cruise control main switch (ON-OFF button). Check that the cruise control indicator (vehicle-to-vehicle distance control mode) in the combination meter assembly and "RADAR READY" on the multi-information display turn off.

(e) Turn the ignition switch off with the cruise control indicator (vehicle-to-vehicle distance control mode) in the combination meter assembly illuminated and "RADAR READY" on the multi-information display displayed. Turn the ignition switch to ON and check the cruise control indicator (vehicle-to-vehicle distance control mode) in the combination meter assembly and "RADAR READY" on the multi-information display are turned off.

INSPECT MODE SELECT

(a) Turn the ignition switch to ON.

(b) Push and hold the cruise control main switch (ON-OFF button) for approximately 1.5 seconds. Check that the cruise control indicator (vehicle-to-vehicle distance control mode) in the combination meter assembly and "RADAR READY" on the multi-information display turn off and the cruise control indicator (constant speed control mode) illuminates.

*a

ON-OFF

(c) Check that the cruise control indicator (vehicle-to-vehicle distance control mode) turns off and the cruise control indicator (constant speed control mode) illuminates.

*1

Cruise Control Indicator

(Vehicle-to-vehicle Distance Control Mode)

*2

Multi-information Display

*3

Cruise Control Indicator

(Constant Speed Control Mode)

NOTICE:

Do not push any other switches before pushing the cruise control main switch to MODE. If any other switch is pushed, turn the dynamic radar cruise control system off and repeat the procedure above.

HINT:

If a malfunction is detected, turn the ignition switch off and repeat the procedure above.

INSPECT STEERING PAD SWITCH ASSEMBLY

(a) Turn the ignition switch to ON.

(b) Turn the dynamic radar cruise control system on using the cruise control main switch (ON-OFF button).

*a

ON-OFF

(c) Press the steering pad switch assembly (distance control switch).

*a

Distance Control Switch

(d) Check that the indicator of the vehicle-to-vehicle distance, which is shown on the multi-information display in the combination meter assembly changes from long to middle to short in that order.

HINT:

Long is automatically selected each time the ignition switch to ON.

System Description
SYSTEM DESCRIPTION GENERAL The cruise control main switch is used to turn the dynamic radar cruise control system on and off, as well as operate 7 functions: SET, - (COAST), TAP-DOWN, RES (RESUM ...

Road Test
ROAD TEST PROBLEM SYMPTOM CONFIRMATION HINT: The dynamic radar cruise control system has 2 cruise control modes: constant speed control mode and vehicle-to-vehicle distance control mode ...

Other materials:

Parking Brake Switch Circuit
DESCRIPTION This circuit is from the parking brake switch assembly to the radio and display receiver assembly. WIRING DIAGRAM PROCEDURE 1. CHECK VEHICLE SIGNAL (a) Display the "Vehicle Signal Check Mode" screen (See page ). ...

Check Mode Procedure
CHECK MODE PROCEDURE 1. DESCRIPTION (a) Check mode has a higher sensitivity to malfunctions and can detect malfunctions that normal mode cannot detect. Check mode can also detect all the malfunctions that normal mode can detect. In check mode, DTCs are detected with 1 trip detection logic. ...

Installation
INSTALLATION PROCEDURE 1. INSTALL FRONT CRANKSHAFT OIL SEAL (a) Using SST and a hammer, tap in a new oil seal until its surface is flush with the timing chain cover assembly edge. SST: 09223-22010 SST: 09506-35010 NOTICE: Keep the lip free from foreign matt ...

В© 2011-2024 Copyright www.ttguide.net