Toyota Tacoma (2015-2018) Service Manual: Multi-terrain Select Switch
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE MULTI-TERRAIN SELECT SWITCH (DRIVE MONITOR SWITCH)
|
(a) Disengage the 2 claws to remove the multi-terrain select switch (drive monitor switch). |
|
.png)
Inspection
INSPECTION
PROCEDURE
1. INSPECT MULTI-TERRAIN SELECT SWITCH (DRIVE MONITOR SWITCH)
(a) Check the resistance.
(1) Measure the resistance according to the value(s) in the table below.
Text in Illustration
|
*1 |
Multi-terrain Select Switch |
|
*a |
MUD and SAND |
|
*b |
LOOSE ROCK |
|
*c |
MOGUL |
|
*d |
ROCK and DIRT |
|
*e |
ROCK |
Text in Illustration
|
*a |
Component without harness connected (Multi-terrain Select Switch (Drive Monitor Switch)) |
Standard Resistance:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
7 (ECU) - 8 (E) |
MUD and SAND |
Below 1 Ω |
|
2 (UP) - 8 (E) |
||
|
6 (DN) - 8 (E) |
10 kΩ or higher |
|
|
7 (ECU) - 8 (E) |
LOOSE ROCK |
Below 1 Ω |
|
2 (UP) - 8 (E) |
10 kΩ or higher |
|
|
6 (DN) - 8 (E) |
||
|
7 (ECU) -8 (E) |
MOGUL |
10 kΩ or higher |
|
2 (UP) -8 (E) |
||
|
6 (DN) -8 (E) |
||
|
7 (ECU) - 8 (E) |
ROCK and DIRT |
10 kΩ or higher |
|
2 (UP) - 8 (E) |
||
|
6 (DN) - 8 (E) |
Below 1 Ω |
|
|
7 (ECU) - 8 (E) |
ROCK |
10 kΩ or higher |
|
2 (UP) - 8 (E) |
Below 1 Ω |
|
|
6 (DN) - 8 (E) |
||
|
1 (SWl1) - 8 (E) |
ON/OFF: Pressed |
Below 1 Ω |
|
ON/OFF: Not pressed |
10 kΩ or higher |
If the result is not as specified, replace the multi-terrain select switch (drive monitor switch).
Installation
INSTALLATION
PROCEDURE
1. INSTALL MULTI-TERRAIN SELECT SWITCH (DRIVE MONITOR SWITCH)
(a) Engage the 2 claws to install the multi-terrain select switch (drive monitor switch).
Front Speed Sensor
Removal
REMOVAL
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting
the cable from the negative (-) battery terminal.
The ...
Rear Speed Sensor
Removal
REMOVAL
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting
the cable from the negative (-) battery terminal.
The ...
Other materials:
Data List / Active Test
DATA LIST / ACTIVE TEST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference
values. Do not depend solely on these reference values when deciding whether a part
is faulty or not.
HINT:
Using the Techstream to read the Data List allows the values or s ...
Transmitter Battery(w/ Smart Key System)
Replacement
REPLACEMENT
CAUTION / NOTICE / HINT
NOTICE:
Take extra care when handling these precision electronic components.
PROCEDURE
1. REMOVE TRANSMITTER BATTERY
(a) Push the release hook knob and extract the mechanical key as shown
in the illustration.
Text in Illustra ...
Ecm
Components
COMPONENTS
ILLUSTRATION
ILLUSTRATION
Installation
INSTALLATION
PROCEDURE
1. INSTALL NO. 2 ECM BRACKET
(a) Install the No. 2 ECM bracket to the ECM with the 2 screws.
Torque:
3.2 N·m {33 kgf·cm, 28 in·lbf}
2. INSTALL ECM BRACKET
(a) Install the ECM bracket to the EC ...
