Toyota Tacoma (2015-2018) Service Manual: Microphone Circuit between Microphone and Radio Receiver

Toyota Tacoma (2015-2018) Service Manual / Navigation / Multi Info Display / Navigation System / Microphone Circuit between Microphone and Radio Receiver

DESCRIPTION

The navigation receiver assembly and telephone microphone assembly are connected to each other using the microphone connection detection signal lines.

Using this circuit, the navigation receiver assembly sends power to the telephone microphone assembly and the telephone microphone assembly sends microphone signals to the navigation receiver assembly.

WIRING DIAGRAM

PROCEDURE

1.	CHECK MICROPHONE

(a) Enter the "Microphone Check" screen. Refer to Check Microphone in Operation Check (See page ).

(b) When a voice is input into the microphone, check that the microphone input level meter changes according to the input voice.

OK:

Check result is normal.

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

2.	CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - TELEPHONE MICROPHONE ASSEMBLY)

(a) Disconnect the N25 navigation receiver assembly connector.

(b) Disconnect the T26 telephone microphone assembly connector.

Standard Resistance:

Tester Connection	Condition	Specified Condition
N25-4 (MACC) - T26-1 (MACC)	Always	Below 1 Ω
N25-5 (MIN+) - T26-2 (MIC+)	Always	Below 1 Ω
N25-19 (MIN-) - T26-4 (MIC-)	Always	Below 1 Ω
N25-6 (SNS2) - T26-3 (SNS2)	Always	Below 1 Ω
N25-4 (MACC) - Body ground	Always	10 kΩ or higher
N25-5 (MIN+) - Body ground	Always	10 kΩ or higher
N25-19 (MIN-) - Body ground	Always	10 kΩ or higher
N25-18 (SGND) - Body ground	Always	10 kΩ or higher
N25-6 (SNS2) - Body ground	Always	10 kΩ or higher

(d) Reconnect the navigation receiver assembly connector.

(e) Reconnect the telephone microphone assembly connector.

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.	INSPECT NAVIGATION RECEIVER ASSEMBLY

(a) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Switch Condition	Specified Condition
N25-4 (MACC) - Body ground	Ignition switch ACC	4 to 6 V

*a	Component with harness connected (Navigation Receiver Assembly)

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
N25-19 (MIN-) - Body ground	Always	Below 1 Ω
N25-18 (SGND) - Body ground	Always	Below 1 Ω

REPLACE NAVIGATION RECEIVER ASSEMBLY

4.	INSPECT TELEPHONE MICROPHONE ASSEMBLY

(a) Remove the telephone microphone assembly (See page ).

*a	Component without harness connected (Telephone Microphone Assembly)

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection	Condition	Specified Condition
3 (SNS2) - 4 (MIC-)	Always	Below 1 Ω

REPLACE TELEPHONE MICROPHONE ASSEMBLY

5.	INSPECT TELEPHONE MICROPHONE ASSEMBLY

(a) Turn the ignition switch to ACC.

*a	Component with harness connected (Telephone Microphone Assembly)

(b) Connect an oscilloscope to terminals 2 (MIC+) and 4 (MIC-) of the telephone microphone assembly connector.

Result

Result	Proceed to
A waveform synchronized with the voice input to the telephone microphone assembly is output	A
A waveform synchronized with the voice input to the telephone microphone assembly is not output	B

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

REPLACE TELEPHONE MICROPHONE ASSEMBLY

Vehicle Speed Signal Circuit between Stereo Component Amplifier and Combination Meter

DESCRIPTION The stereo component amplifier assembly receives a vehicle speed signal from the combination meter assembly to control the ASL function. HINT: A voltage of 12 V or 5 V is outp ...

Radio Receiver Power Source Circuit

DESCRIPTION This is the power source circuit to operate the navigation receiver assembly. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this s ...

Other materials:

Short in Front Passenger Side Squib 2nd Step Circuit (B1815/54-B1818/54)
DESCRIPTION The front passenger side squib 2nd step circuit consists of the airbag sensor assembly and the instrument panel passenger without door airbag assembly. The circuit signals the SRS to deploy when airbag deployment conditions are met. These DTCs are set when a malfunction is detected ...

Off-road precautions (4WD models and PreRunner)
This vehicle has higher ground clearance and narrower tread in relation to the height of its center of gravity to make it capable of performing in a wide variety of off-road applications. Off-road vehicle feature ● Specific design characteristics give it a higher center of gravity than o ...

Removal
REMOVAL PROCEDURE 1. REMOVE REAR SEAT CUSHION ASSEMBLY 2. REMOVE NO. 4 ROOM PARTITION COVER LH 3. REMOVE NO. 4 ROOM PARTITION COVER RH 4. REMOVE NO. 3 ROOM PARTITION COVER 5. REMOVE BACK PANEL GARNISH HOLE PLUG 6. REMOVE BACK PANEL TRIM 7. REMOVE FRONT DOOR SCUFF PLATE ...