Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Main Switch Signal Circuit

DESCRIPTION

When the wireless charger main switch (mobile wireless charger switch) is turned on, this circuit sends an on signal to the mobile wireless charger cradle assembly using the power supplied to the wireless charger main switch (mobile wireless charger switch).

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE

1.

INSPECT WIRELESS CHARGER MAIN SWITCH (MOBILE WIRELESS CHARGER SWITCH)

(a) Remove the wireless charger main switch (mobile wireless charger switch) (See page ).

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

M7-11 (ACC) - M7-12 (GND)

Wireless Charger Main Switch (Mobile Wireless Charger Switch) is on (not protruding)

Below 1 Ω

Wireless Charger Main Switch (Mobile Wireless Charger Switch) is off (protruding)

10 kΩ or higher

Text in Illustration

*a

Component without harness connected

(Wireless Charger Main switch (Mobile Wireless Charger Switch))

NG

REPLACE WIRELESS CHARGER MAIN SWITCH (MOBILE WIRELESS CHARGER SWITCH)

OK

2.

CHECK TERMINAL VOLTAGE (WIRELESS CHARGER MAIN SWITCH - BATTERY AND GROUND)

(a) Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

M7-11 (ACC) - Body ground

Ignition Switch ACC

11 to 14 V

Standard Resistance:

Tester Connection

Condition

Specified Condition

M7-12 (GND) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

CHECK HARNESS AND CONNECTOR (WIRELESS CHARGER MAIN SWITCH - MOBILE WIRELESS CHARGER CRADLE ASSEMBLY)

(a) Disconnect the M5 mobile wireless charger cradle assembly connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

M5-3 (SW) - M7-8 (SW)

Always

Below 1 Ω

OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

Wireless Charger Power Source Circuit
DESCRIPTION This is the power source circuit to operate the mobile wireless charger cradle assembly. WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to t ...

Status Signal Circuit
DESCRIPTION This circuit sends a smart key system status signal from the certification ECU (smart key ECU assembly) to the mobile wireless charger cradle assembly. Based on this signal, the mobil ...

Other materials:

Listening to an iPod
Connecting an iPod enables you to enjoy music from the vehicle speakers. Select “iPod” on the “Select Audio Source” screen. When the iPod connected to the system includes iPod video, the system can only output the sound by selecting the browse screen. Connecting an iPod Audio control s ...

Acceleration Sensor Stuck Malfunction (C1232,C1243,C1245,C1279)
DESCRIPTION The skid control ECU (master cylinder solenoid) receives signals from the yaw rate and acceleration (airbag sensor assembly) via the CAN communication system. The airbag sensor assembly has a built-in yaw rate and acceleration sensor and detects the vehicle's condition using 2 ...

Terminals Of Ecu
TERMINALS OF ECU 1. CHECK COMBINATION METER ASSEMBLY (a) Measure the resistance and voltage according to the value(s) in the table below. Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition ...

© 2011-2024 Copyright www.ttguide.net