DESCRIPTION
The stereo component tuner assembly and the radio and display receiver assembly are connected by an LVDS communication line.
This DTC is stored when an LVDS communication error occurs between the stereo component tuner assembly and the radio and display receiver assembly.
DTC Code |
DTC Detection Condition |
Trouble Area |
---|---|---|
B1532 |
When any of the following conditions is met:
|
|
HINT:
Even if no malfunction is present, this DTC may be stored depending on the battery condition or engine start voltage.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
After replacing the stereo component tuner assembly of vehicles subscribed to pay-type satellite radio broadcasts, XM radio ID registration is necessary.
PROCEDURE
1. |
CHECK NO. 1 NAVIGATION WIRE (STEREO COMPONENT TUNER ASSEMBLY POWER SOURCE) |
(a) Disconnect the stereo component tuner assembly connector. |
|
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
S52-8 (GND2) - Body ground |
Always |
Below 1 Ω |
(c) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection |
Switch Condition |
Specified Condition |
---|---|---|
S52-4 (+B2) - S52-8 (GND2) |
Always |
11 to 14 V |
S52-3 (ACC2) - S52-8 (GND2) |
Ignition switch ACC |
11 to 14 V |
*a |
Front view of wire harness connector (to Stereo Component Tuner Assembly) |
NG |
GO TO STEP 4 |
|
2. |
REPLACE NO. 1 NAVIGATION WIRE |
(a) Replace the No. 1 navigation wire with a new or known good one (See page ).
(b) Clear the DTCs (See page ).
(c) Recheck for DTCs and check that no DTCs are output.
OK:
No DTCs are output.
OK |
END |
|
3. |
REPLACE STEREO COMPONENT TUNER ASSEMBLY |
(a) Replace the stereo component tuner assembly with a new or known good one (See page ).
(b) Clear the DTCs (See page ).
(c) Recheck for DTCs and check that no DTCs are output.
OK:
No DTCs are output.
OK |
END |
NG |
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
4. |
CHECK NO. 1 NAVIGATION WIRE |
(a) Disconnect the R27 radio and display receiver assembly connector.
(b) Disconnect the S52 stereo component tuner assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
R27-4 (+B2) - S52-4 (+B2) |
Always |
Below 1 Ω |
R27-3 (ACC2) - S52-3 (ACC2) |
Always |
Below 1 Ω |
R27-8 (GND2) - S52-8 (GND2) |
Always |
Below 1 Ω |
R27-4 (+B2) - Body ground |
Always |
10 kΩ or higher |
R27-3 (ACC2) - Body ground |
Always |
10 kΩ or higher |
R27-8 (GND2) - Body ground |
Always |
10 kΩ or higher |
OK |
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
NG |
REPLACE NO. 1 NAVIGATION WIRE |
Outside Vehicle
General Maintenance
GENERAL MAINTENANCE
CAUTION / NOTICE / HINT
Performing these maintenance checks on the vehicle is the owner's responsibility.
The owner may perform the maintenance or take the vehicle to a service center.
Check the parts of the vehicle described below on a daily basis ...
Interior
*1: If equipped
* 2: Access Cab and Double Cab models
*3: Vehicles with auto anti- glare inside rear view mirror
*1: If equipped
*2: Vehicles with an automatic transmission
* : If equipped
* 1: If equipped
* 2: Vehicles with sub woofer ...
Inspection
INSPECTION
PROCEDURE
1. INSPECT FRONT SEATBACK HEATER ASSEMBLY
(a) Check the operation of the front seatback heater assembly.
(1) Apply battery voltage and check the operation of the front seatback
heater assembly.
OK:
Connection
Conditio ...