DESCRIPTION
This DTC is stored when a communication error occurs between the navigation receiver assembly and combination meter assembly.
DTC No. |
DTC Detection Condition |
Trouble Area |
---|---|---|
B1324 |
After the navigation receiver assembly receives a registration information signal, which is sent by the combination meter assembly when the ignition switch is ACC, 1 or more times, the navigation receiver assembly cannot receive the signal for 30 seconds or more. |
|
WIRING DIAGRAM
PROCEDURE
1. |
CHECK HARNESS AND CONNECTOR (NAVIGATION RECEIVER ASSEMBLY - COMBINATION METER ASSEMBLY) |
(a) Disconnect the N26 navigation receiver assembly connector.
(b) Disconnect the C9 combination meter assembly connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
N26-3 (CNH1) - C9-4 (MSCH) |
Always |
Below 1 Ω |
N26-4 (CNL1) - C9-5 (MSCL) |
Always |
Below 1 Ω |
N26-3 (CNH1) - Body ground |
Always |
10 kΩ or higher |
N26-4 (CNL1) - Body ground |
Always |
10 kΩ or higher |
N26-3 (CNH1) - N26-4 (CNL1) |
Always |
10 kΩ or higher |
(d) Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
N26-3 (CNH1) - Body ground |
Always |
Below 1 V |
N26-4 (CNL1) - Body ground |
Always |
Below 1 V |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
2. |
INSPECT COMBINATION METER ASSEMBLY |
(a) Remove the combination meter assembly (See page ).
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
NG |
REPLACE COMBINATION METER ASSEMBLY |
|
3. |
INSPECT NAVIGATION RECEIVER ASSEMBLY |
(a) Remove the navigation receiver assembly (See page ).
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
NG |
REPLACE NAVIGATION RECEIVER ASSEMBLY |
|
4. |
REPLACE COMBINATION METER ASSEMBLY |
(a) Replace the combination meter assembly with a new or known good one (See page ).
(b) Clear the DTCs (See page ).
(c) Recheck for DTCs and check that no DTCs are output.
OK:
No DTCs are output.
NG |
REPLACE NAVIGATION RECEIVER ASSEMBLY |
|
5. |
CHECK METER / GAUGE SYSTEM |
(a) Turn the ignition switch to ON and wait 30 seconds.
(b) Operate the steering pad switch assembly and check that the audio tab is displayed on the multi-information display in the combination meter assembly and the audio system can be operated normally.
OK:
Audio system returns to normal.
OK |
END |
NG |
REPLACE NAVIGATION RECEIVER ASSEMBLY |
Front Differential Oil Temperature Sensor Circuit High (P17C8)
DESCRIPTION
This DTC is output when a short to B+ or open circuit in the oil temperature
sensor is detected.
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
P17C8
Front Differential Oil Temperature Sensor Circuit ...
Traffic Information is not Displayed
CAUTION / NOTICE / HINT
NOTICE:
Traffic information requires payment. An "XM Nav Traffic" contract must
be made between the satellite radio company and the user. If the contract
expires, traffic information will not be available.
Traffic information does not apply to ...
Unable to Unlock Steering Wheel (Engine cannot Start)
DESCRIPTION
The steering lock actuator assembly activates the steering lock motor and moves
the lock bar into the steering column to lock the steering.
The steering may not unlock when the lock bar gets stuck in the lock hole of
the steering column. In this case, if the engine switch is turned ...