Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Lock Switch Circuit

WIRING DIAGRAM

PROCEDURE

PROCEDURE

1.

CHECK REAR DIFFERENTIAL LOCK INDICATOR LIGHT

(a) Turn the ignition switch to ON.

(b) for 4WD:

Finish switching to L4.

(c) Check the rear differential lock indicator light.

(d) Press the differential lock switch.

(e) After 60 seconds, check the rear differential lock indicator light.

Result

Result

Proceed to

Rear differential lock indicator light blinks or illuminates

A

Rear differential lock indicator light remains off regardless of switch operation

B

Rear differential lock indicator light remains illuminated regardless of switch operation

C

Rear differential lock indicator light rapidly blinks

D

  • Blinking: Blinks at 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
  • Rapidly blinking: Blinks at 0.25 second intervals (0.25 seconds on and 0.25 seconds off)
A

END

C

GO TO STEP 8

D

GO TO DTC P17CC

B

2.

CHECK CAN COMMUNICATION LINE

(a) Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus (See page OK: OK: ).

OK:

"Bus Check" indicates no malfunctions in CAN communication.

NG

CHECK CAN COMMUNICATION SYSTEM

OK

3.

READ VALUE USING TECHSTREAM (REAR DIFFERENTIAL LOCK SWITCH CONTROL SW (R))

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the Techstream on.

(d) Turn the ignition switch to ON.

(e) Enter the following menus: Powertrain / Four Wheel Drive / Data List.

(f) According to the display on the Techstream, read the Data List.

Four Wheel Drive

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Rear Differential Lock Control SW (R)

Differential lock switch status (differential lock switch input signal of R terminal on ECU side)/

ON or OFF

ON: Switch pressed and held

OFF: Switch not pressed

-

OK:

Display changes according to differential lock switch operation.

NG

GO TO STEP 5

OK

4.

INSPECT COMBINATION METER ASSEMBLY

(a) Turn the ignition switch off.

(b) Perform Active Test of the combination meter assembly using the Techstream.

(c) Check the combination meter assembly.

OK:

The rear differential lock indicator light turns on or off in accordance with the Techstream.

OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

CHECK METER / GAUGE SYSTEM

5.

INSPECT DIFFERENTIAL LOCK SWITCH

(a) Disconnect the G13 differential lock switch connector.

(b) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Switch Condition

Specified Condition

6 - 3

Switch not pressed

10 kΩ or higher

6 - 3

Switch pressed

Below 1 Ω

Text in Illustration

*a

Component without harness connected

(Differential Lock Switch)

NG

REPLACE DIFFERENTIAL LOCK SWITCH

OK

6.

INSPECT ROOF CONSOLE BOX ASSEMBLY

(a) Remove the roof console box assembly.

  • for Double Cab: (See page ) for Access Cab: (See page )
  • for Access Cab: (See page ) )
Text in Illustration

*a

Component without harness connected

(Roof Console Box Assembly)

-

-

(b) Measure the resistance according the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

R44-6 (B) - 6 (B)

Always

Below 1 Ω

R44-12 (GND) - 3 (E)

Always

Below 1 Ω

Result

Result

Proceed to

OK

A

NG (for Double Cab)

B

NG (for Access Cab)

C

B

REPLACE ROOF CONSOLE BOX ASSEMBLY

C

REPLACE ROOF CONSOLE BOX ASSEMBLY

A

7.

CHECK HARNESS AND CONNECTOR (4 WHEEL DRIVE CONTROL ECU - ROOF CONSOLE BOX ASSEMBLY)

(a) Disconnect the F13 4 wheel drive control ECU connector.

(b) Disconnect the R44 roof console box assembly connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

F13-15 (R) - R44-6 (B)

Always

Below 1 Ω

R44-12 (GND) - Body ground

Always

Below 1 Ω

OK

REPLACE 4 WHEEL DRIVE CONTROL ECU

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

8.

CHECK CAN COMMUNICATION LINE

(a) Select "Bus Check" from the System Selection Menu screen, and follow the prompts on the screen to inspect the CAN Bus (See page OK: OK: ).

OK:

"Bus Check" indicates no malfunctions in CAN communication.

NG

CHECK CAN COMMUNICATION SYSTEM

OK

9.

READ VALUE USING TECHSTREAM (REAR DIFFERENTIAL LOCK INDICATOR REQUEST)

(a) Turn the ignition switch off.

(b) Connect the Techstream to the DLC3.

(c) Turn the Techstream on.

(d) Turn the ignition switch to ON.

(e) Enter the following menus: Powertrain / Four Wheel Drive / Data List.

(f) According to the display on the Techstream, read the Data List.

Four Wheel Drive

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

Rear Differential Lock Indicator Request

Rear differential lock indicator light request/

Blink4*, Blink3, Blink2, Blink1, ON or OFF

  • Blink3: Indicator light rapidly blinks
  • Blink2: Indicator light blinks 3 times
  • Blink1: Indicator light blinks
  • ON: Indicator light illuminates
  • OFF: Indicator light turns off
  • Blinking: 0.5 second intervals (0.5 seconds on and 0.5 seconds off)
  • Rapidly blinking: 0.25 second intervals (0.25 seconds on and 0.25 seconds off)

*: Item not supported, therefore not displayed

(g) for 4WD:

Finish switching to L4.

(h) Turn the differential lock switch on and off several times and check the Techstream display condition of the rear differential lock indicator light.

Result

Result

Proceed to

Data List continues to display ON even when differential lock switch is operated

A

Data List display changes according to differential lock switch operation

B

A

REPLACE 4 WHEEL DRIVE CONTROL ECU

B

CHECK METER / GAUGE SYSTEM

ECU Power Source Circuit
WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before performing the following inspection procedure. PROCEDURE 1. ...

Lost Communication With Vehicle Dynamics Control Module (U0122)
DESCRIPTION This DTC is detected if communication is lost with the skid control ECU (brake actuator assembly). DTC No. Detection Item DTC Detection Condition ...

Other materials:

Slip Indicator Light Remains ON
DESCRIPTION The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication. The slip indicator light blinks during VSC and/or TRAC operation. If a malfunction is detected, the slip indicator light comes on to warn the driver (See page ). ...

Problem Symptoms Table
PROBLEM SYMPTOMS TABLE Use the table below to help determine the cause of problem symptoms. If multiple suspected areas are listed, the potential causes of the symptoms are listed in order of probability in the "Suspected Area" column of the table. Check each symptom by ...

Operation Check
OPERATION CHECK 1. CHECK FUNCTION (a) Check that the key reminder warning buzzer sounds. (1) With the driver side door closed, insert the key into the ignition key cylinder and then turn the key to LOCK or ACC. (2) Check that the buzzer sounds intermittently when the driver side door is open ...

© 2011-2024 Copyright www.ttguide.net