INSTALLATION
PROCEDURE
1. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 1)
(a) Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly in the locations shown in the illustration. Text in Illustration
|
|
(b) Install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with 2 new bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
Be careful that the O-ring is not jammed.
(c) Connect the connector to the camshaft timing oil control solenoid assembly.
2. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 1)
(a) Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly in the locations shown in the illustration. Text in Illustration
|
|
(b) Install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with 2 new bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
Be careful that the O-ring is not jammed.
(c) Connect the connector to the camshaft timing oil control solenoid assembly.
3. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Intake Side of Bank 2)
(a) Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly in the locations shown in the illustration. Text in Illustration
|
|
(b) Install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with 2 new bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
Be careful that the O-ring is not jammed.
(c) Connect the connector to the camshaft timing oil control solenoid assembly.
4. INSTALL CAMSHAFT TIMING OIL CONTROL SOLENOID ASSEMBLY (for Exhaust Side of Bank 2)
(a) Apply engine oil to a new O-ring and install it to the camshaft timing oil control solenoid assembly in the locations shown in the illustration. Text in Illustration
|
|
(b) Install the camshaft timing oil control solenoid assembly to the timing chain cover assembly with 2 new bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
NOTICE:
Be careful that the O-ring is not jammed.
(c) Connect the connector to the camshaft timing oil control solenoid assembly.
5. INSTALL THROTTLE BODY BRACKET
(a) Install the throttle body bracket to the intake air surge tank assembly and timing chain cover assembly with the 2 bolts.
Torque:
21 N·m {214 kgf·cm, 15 ft·lbf}
6. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE
(a) Apply engine oil to a new O-ring and install it to the engine oil level dipstick guide.
(b) Install the engine oil level dipstick guide to the timing chain cover assembly and oil pan sub-assembly with the bolt.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
(c) Engage the clamp to install the wire harness.
(d) Install the engine oil level dipstick.
7. INSTALL AIR CLEANER CAP AND HOSE
8. INSTALL V-BANK COVER SUB-ASSEMBLY
9. INSTALL FRONT FENDER SEAL RH
HINT:
Use the same procedure as for the LH side (See page ).
Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL UPPER RADIATOR TANK
(a) Install a new upper radiator tank.
Text in Illustration
*1
Upper Radiator Tank
*2
Core Plate
*a
Correc ...
Inspection
INSPECTION
PROCEDURE
1. INSPECT WINDSHIELD WIPER MOTOR ASSEMBLY
(a) Check the LO operation.
Text in Illustration
*a
Component without harness connected
(Windshield Wiper Motor Assembly)
(1) Apply battery voltage to the windshield wiper motor connector and ch ...
Initialization
INITIALIZATION
1. RESET MEMORY
NOTICE:
Perform Reset Memory (AT initialization) when replacing the automatic
transmission assembly, transmission valve body assembly or any of the shift
solenoid valves.
Reset Memory can be performed only with the Techstream.
HINT:
The E ...