Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Installation

INSTALLATION

PROCEDURE

1. INSTALL ENGINE WATER PUMP ASSEMBLY

(a) Install the engine water pump assembly and a new gasket to the timing chain cover assembly with the 15 bolts.

Torque:

for Bolt A and B :

11 N·m {112 kgf·cm, 8 ft·lbf}

for Bolt C :

21 N·m {214 kgf·cm, 15 ft·lbf}

for Bolt D :

43 N·m {438 kgf·cm, 32 ft·lbf}

NOTICE:

  • Be sure to apply adhesive to the 2 bolts labeled B before reusing them, or replace them with new ones if necessary.

    Adhesive:

    Toyota Genuine Adhesive 1344, Three Bond 1344 or equivalent

  • Make sure that there is no oil on the threads of the bolts labeled C, D.

2. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

(a) Install the 2 No. 2 idler pulley sub-assemblies to the timing chain cover assembly with the 2 bolts.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

3. INSTALL VANE PUMP ASSEMBLY

(a) Install the vane pump assembly to the timing chain cover assembly with the 2 bolts.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

4. INSTALL V-RIBBED BELT TENSIONER ASSEMBLY

5. INSTALL COOLER COMPRESSOR ASSEMBLY

5. INSTALL COOLER COMPRESSOR ASSEMBLY

(See page 6. INSTALL FAN SHROUD 6. INSTALL FAN SHROUD )

6. INSTALL FAN SHROUD

7. INSTALL TRANSMISSION OIL COOLER HOSE (for Automatic Transmission)

7. INSTALL TRANSMISSION OIL COOLER HOSE (for Automatic Transmission)

(a) Engage the clamp to install the 2 transmission oil cooler hoses to the fan shroud.

8. CONNECT RADIATOR RESERVE TANK HOSE

9. INSTALL NO. 2 RADIATOR HOSE

9. INSTALL NO. 2 RADIATOR HOSE

10. INSTALL NO. 1 RADIATOR HOSE

10. INSTALL NO. 1 RADIATOR HOSE

11. INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

11. INSTALL WATER INLET WITH THERMOSTAT SUB-ASSEMBLY

(See page 2gr-fks Emission Control )

Removal
REMOVAL PROCEDURE 1. REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY (See page ) 2. REMOVE NO. 1 RADIATOR HOSE 3. REMOVE NO. 2 RADIATOR HOSE 4. DISCONNECT RADIATOR RESERVE TANK HOSE 5 ...

2gr-fks Emission Control
...

Other materials:

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: The following procedures are for BD20 (w/o Differential Lock). PROCEDURE 1. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY (a) Clean the contact surfaces of the rear differential carrier assembly and axle housing. (b) Install the rear differ ...

Side Moulding
Components COMPONENTS ILLUSTRATION ILLUSTRATION Removal REMOVAL CAUTION / NOTICE / HINT HINT: Use the same procedure for the RH side and LH side. The following procedure is for the LH side. When removing the lower No. 2 side panel moulding, heat the vehicle body a ...

How To Proceed With Troubleshooting
PROCEDURE 1. CHECK TIRE AND WHEEL SYSTEM DIAGNOSIS OF IRREGULAR TIRE WEAR GO TO STEP 11 DIAGNOSIS OF TIRE VIBRATION 2. TIGHTEN WHEEL NUTS ...

© 2011-2024 Copyright www.ttguide.net