Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Installation

INSTALLATION

PROCEDURE

1. INSTALL GENERATOR ASSEMBLY

(a) Install the generator bracket to the generator assembly with the bolt.

Torque:

20 N·m {204 kgf·cm, 15 ft·lbf}

(b) Install the generator assembly with the 2 bolts.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

(c) Connect the generator bracket to the cylinder block sub-assembly with the bolt.

Torque:

20 N·m {204 kgf·cm, 15 ft·lbf}

(d) Engage the clamp and connect the engine wire to the generator bracket.

(e) Connect the engine wire to the generator assembly with the 2 bolts.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

(f) Connect the engine wire to the terminal B with the nut.

Torque:

9.8 N·m {100 kgf·cm, 87 in·lbf}

(g) Install the terminal cap.

(h) Connect the connector to the generator assembly .

(i) Install the wire harness clamp bracket with the bolt.

Torque:

8.0 N·m {82 kgf·cm, 71 in·lbf}

(j) Engage the clamp and install the engine wire to the wire harness clamp bracket.

2. INSTALL NO. 1 SURGE TANK STAY

Click here 3. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

3. INSTALL NO. 2 IDLER PULLEY SUB-ASSEMBLY

(a) Install the No. 2 idler pulley sub-assembly with the bolt.

Torque:

43 N·m {438 kgf·cm, 32 ft·lbf}

4. INSTALL V-BANK COVER

Click here 5. INSTALL BATTERY TRAY

5. INSTALL BATTERY TRAY

6. INSTALL BATTERY

7. INSTALL BATTERY CLAMP SUB-ASSEMBLY

(a) Install the battery clamp sub-assembly and tighten the nut.

Torque:

5.4 N·m {55 kgf·cm, 48 in·lbf}

8. CONNECT CABLE TO POSITIVE BATTERY TERMINAL

Torque:

5.4 N·m {55 kgf·cm, 48 in·lbf}

9. CONNECT CABLE TO NEGATIVE TERMINAL

Torque:

5.4 N·m {55 kgf·cm, 48 in·lbf}

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here Reassembly

Inspection
INSPECTION PROCEDURE 1. INSPECT GENERATOR BRUSH HOLDER ASSEMBLY (a) Using a vernier caliper, measure the brush length. Text in Illustration *a Len ...

Reassembly
REASSEMBLY PROCEDURE 1. INSTALL GENERATOR DRIVE END FRAME BEARING (a) Using SST and a press, press in a new generator drive end frame bearing. SST: 09950-60010 09951-00470 SST: ...

Other materials:

Steering wheel
The steering wheel can be adjusted to a comfortable position. Hold the steering wheel and press the lever down. Adjust to the ideal position by moving the steering wheel horizontally and vertically. After adjustment, pull the lever up to secure the steering wheel. CAUTION ■Caution whi ...

System Description
SYSTEM DESCRIPTION 1. POWER DOOR LOCK CONTROL SYSTEM DESCRIPTION (a) The power door lock system locks/unlocks all the doors. The main body ECU (multiplex network body ECU) receives lock/unlock request signals from a door control switch or the driver door key lock and unlock switch. Then, the ...

Air conditioning filter
The air conditioning filter must be changed regularly to maintain air conditioning efficiency. ■ Removal method Turn the engine switch to the LOCK position. Open the glove box. Slide off the damper. Push in each side of the glove box to disconnect the claws. Open the filter ...

© 2011-2022 Copyright www.ttguide.net