Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Installation

INSTALLATION

PROCEDURE

1. INSTALL REAR BRAKE DRUM SUB-ASSEMBLY

(a) Install a new drum gasket onto the rear brake drum.

(b) Install the rear brake drum.

2. ADJUST REAR DRUM BRAKE SHOE CLEARANCE

(a) Provisionally install the hub nuts.

(a) Provisionally install the hub nuts.

(b) Remove the hole plug, and turn the adjuster to expand the shoe until the drum locks.

(c) Using a screwdriver, release the adjuster 15 notches.

(d) Install the hole plug.

3. FILL RESERVOIR WITH BRAKE FLUID (for Hydraulic Brake Booster)

4. FILL RESERVOIR WITH BRAKE FLUID (for Vacuum Brake Booster)

4. FILL RESERVOIR WITH BRAKE FLUID (for Vacuum Brake Booster)

5. BLEED BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY (for Hydraulic Brake Booster)

5. BLEED BRAKE BOOSTER WITH ACCUMULATOR PUMP ASSEMBLY (for Hydraulic Brake Booster)

6. BLEED MASTER CYLINDER (for Vacuum Brake Booster)

6. BLEED MASTER CYLINDER (for Vacuum Brake Booster)

7. BLEED BRAKE LINE (for Hydraulic Brake Booster)

7. BLEED BRAKE LINE (for Hydraulic Brake Booster)

8. BLEED BRAKE LINE (for Vacuum Brake Booster)

8. BLEED BRAKE LINE (for Vacuum Brake Booster)

9. BLEED MASTER CYLINDER SOLENOID (for Hydraulic Brake Booster)

9. BLEED MASTER CYLINDER SOLENOID (for Hydraulic Brake Booster)

10. BLEED BRAKE ACTUATOR (for Vacuum Brake Booster)

10. BLEED BRAKE ACTUATOR (for Vacuum Brake Booster)

11. INSPECT FLUID LEVEL IN RESERVOIR (for Hydraulic Brake Booster)

11. INSPECT FLUID LEVEL IN RESERVOIR (for Hydraulic Brake Booster)

12. INSPECT FLUID LEVEL IN RESERVOIR (for Vacuum Brake Booster)

12. INSPECT FLUID LEVEL IN RESERVOIR (for Vacuum Brake Booster)

13. INSPECT FOR BRAKE FLUID LEAK

13. INSPECT FOR BRAKE FLUID LEAK

14. INSTALL REAR WHEEL

Torque:

113 N·m {1152 kgf·cm, 83 ft·lbf}

15. INSPECT PARKING BRAKE PEDAL TRAVEL

16. ADJUST PARKING BRAKE PEDAL TRAVEL

16. ADJUST PARKING BRAKE PEDAL TRAVEL

Vacuum Pump

Reassembly
REASSEMBLY PROCEDURE 1. INSTALL REAR WHEEL CYLINDER CUP KIT (a) Provisionally tighten the bleeder plug to the rear wheel brake cylinder, and install the bleeder plug cap. (b) Apply lithium soa ...

Vacuum Pump
Components COMPONENTS ILLUSTRATION Installation INSTALLATION PROCEDURE 1. INSTALL VACUUM PUMP ASSEMBLY (a) Apply engine oil to the 2 O-rings on the vacuum pump assembly. (b) Apply engine ...

Other materials:

Lost Communication with ECM / PCM "A" (U0100,U0126,U0129,U0142)
DESCRIPTION These DTCs are stored if there is a malfunction in the CAN communication system connected to the blind spot monitor sensor. HINT: If CAN communication system DTCs are stored, they may also be stored for other systems. DTC Code DTC Detection Condition ...

Sensor (Motor) Failure (B2341,B2344)
DESCRIPTION When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a motor malfunction and the sliding roof operation is stopped, DTC B2341 is stored. When the sliding roof ECU (sliding roof drive gear sub-assembly) detects a gear position malfunction and the sliding roof ope ...

Brake Signal Malfunction (B2284)
DESCRIPTION This DTC is stored when the brake signal sent via direct line and the brake signal sent via CAN communication do not match. HINT: When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the ca ...

© 2011-2024 Copyright www.ttguide.net