Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Installation

INSTALLATION

CAUTION / NOTICE / HINT

CAUTION:

Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page ).

HINT:

  • Use the same procedure for both the RH and LH sides.
  • The procedure described below is for the LH side.

PROCEDURE

1. INSTALL FRONT AIRBAG SENSOR

(a) Check that the ignition switch is off.

(b) Check that the cable is disconnected from the negative (-) battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(c) Connect the connector to the front airbag sensor.

NOTICE:

When connecting any airbag connector, take care not to damage the airbag wire harness.

(1) Before connecting the connector, check that the position of the white housing lock is correct as shown in the illustration.

*a

Incorrect

*b

Correct

(2) Be sure to engage the connectors until they are locked (when locking, make sure that a click sound can be heard).

Text in Illustration

*1

Housing Lock

*2

CPA

*a

Connection is Completed

-

-

HINT:

When engaged, the white housing lock will slide. Be sure not to hold the white housing lock and part (A), as it may result in an insecure fit.

(d) Engage the 2 claws into the body hole and install the front airbag sensor with the 2 bolts.

Torque:

9.0 N·m {92 kgf·cm, 80 in·lbf}

NOTICE:

  • If the front airbag sensor has been dropped, or there are any cracks, dents or other defects in the case or connector, replace it with a new one.
  • When installing the front airbag sensor, be careful that the SRS wiring does not interfere with or is not pinched between other parts.
  • Make sure that the 2 claws (stopper) is securely inserted into the body hole.
  • Tighten the bolt while holding the front airbag sensor because the front airbag sensor 2 claws (stopper) is easily damaged.

(e) Check that there is no looseness in the installation parts of the front airbag sensor.

2. INSTALL RADIATOR SIDE DEFLECTOR

3. INSTALL RADIATOR GRILLE

3. INSTALL RADIATOR GRILLE

4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

4. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:

5.4 N·m {55 kgf·cm, 48 in·lbf}

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 5. INSPECT SRS WARNING LIGHT

5. INSPECT SRS WARNING LIGHT

Click here Removal

On-vehicle Inspection
ON-VEHICLE INSPECTION CAUTION / NOTICE / HINT CAUTION: Be sure to correctly follow the removal and installation procedures for the front airbag sensors. PROCEDURE 1. INSPECT FRONT AIRBAG SENSOR ...

Removal
REMOVAL CAUTION / NOTICE / HINT CAUTION: Some of these service operations affect the SRS airbag system. Read the precautionary notices concerning the SRS airbag system before servicing (See page ...

Other materials:

High Pitched Horn
Components COMPONENTS ILLUSTRATION Removal REMOVAL PROCEDURE 1. REMOVE RADIATOR GRILLE Click here 2. REMOVE HIGH PITCHED HORN ASSEMBLY (a) Disconnect the connector. (b) Remove the bolt and high pitched horn assembly. Inspection ...

Terminals Of Ecu
TERMINALS OF ECU 1. AIR CONDITIONING AMPLIFIER ASSEMBLY HINT: Check from the rear of the connector while it is connected to the air conditioning amplifier assembly. Terminal No. (Symbol) Wiring Color Terminal Description Condition Spe ...

Terminals Of Ecu
TERMINALS OF ECU 1. BLIND SPOT MONITOR SENSOR LH (MASTER) Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition B12-3 (BIND) - B12-10 (BLGD) Y - W-B Blind spot monitor ...

© 2011-2024 Copyright www.ttguide.net