INSTALLATION
PROCEDURE
1. ADJUST COMPRESSOR OIL
(a) for HFC-134a (R134a):
(1) When replacing the compressor and magnetic clutch with new ones, after gradually discharging the refrigerant gas from the service valve, drain the following volume of oil from new compressor and magnetic clutch before installation.
Standard:
(Oil capacity inside a new compressor and magnetic clutch: 150 + 15 cc (5.1 + 0.51 fl.oz.)) - (Remaining oil amount in the removed compressor and magnetic clutch) = (Oil amount to be removed when replacing the compressor)
NOTICE:
(b) for HFO-1234yf (R1234yf):
(1) When replacing the compressor and magnetic clutch with new ones, after gradually discharging the refrigerant gas from the service valve, drain the following volume of oil from new compressor and magnetic clutch before installation.
Standard:
(Oil capacity inside a new compressor and magnetic clutch: 150 + 15 cc (5.1 + 0.51 fl.oz.)) - (Remaining oil amount in the removed compressor and magnetic clutch) = (Oil amount to be removed when replacing the compressor)
NOTICE:
2. INSTALL COOLER COMPRESSOR ASSEMBLY (for 2TR-FE)
(a) Using an E8 ''TORX'' socket wrench, temporarily install the cooler compressor assembly with the 2 stud bolts.
Torque:
10 N·m {102 kgf·cm, 7 ft·lbf}
(b) Install the 2 nuts and 2 bolts in the order shown in the illustration. Torque: 21 N·m {214 kgf·cm, 16 ft·lbf} |
|
(c) Connect the connector.
3. INSTALL COOLER COMPRESSOR ASSEMBLY (for 2GR-FKS)
(a) Using an E8 ''TORX'' socket wrench, temporarily install the cooler compressor assembly with the 2 stud bolts.
(b) Install the 2 nuts and 2 bolts in the order shown in the illustration. Torque: 21 N·m {214 kgf·cm, 16 ft·lbf} |
|
(c) Connect the connector.
4. INSTALL DISCHARGE HOSE SUB-ASSEMBLY
(a) Remove the vinyl tape from discharge hose sub-assembly and connecting portion of the cooler compressor assembly.
(b) Apply sufficient compressor oil to a new O-ring and fitting surface of the cooler compressor assembly.
Compressor oil:
PSD1 or equivalent
(c) Install the O-ring to the discharge hose sub-assembly.
(d) Install the discharge hose sub-assembly to the cooler compressor assembly with the bolt.
Torque:
9.8 N·m {100 kgf·cm, 87 in·lbf}
5. INSTALL SUCTION HOSE SUB-ASSEMBLY (for 2TR-FE)
(a) Remove the vinyl tape from the suction hose sub-assembly.
(b) Apply sufficient compressor oil to a new O-ring and fitting surface of the cooler compressor assembly.
Compressor oil:
PSD1 or equivalent
(c) Install the O-ring to the suction hose sub-assembly.
(d) Install the suction hose sub-assembly to the cooler compressor assembly with the bolt.
Torque:
9.8 N·m {100 kgf·cm, 87 in·lbf}
(e) Install the suction hose sub-assembly with the bolt.
Torque:
7.5 N·m {76 kgf·cm, 66 in·lbf}
6. INSTALL SUCTION HOSE SUB-ASSEMBLY (for 2GR-FKS)
(a) Remove the vinyl tape from the suction hose sub-assembly.
(b) Apply sufficient compressor oil to a new O-ring and fitting surface of the cooler compressor assembly.
Compressor oil:
PSD1 or equivalent
(c) Install the O-ring to the suction hose sub-assembly.
(d) Install the suction hose sub-assembly to the cooler compressor assembly with the bolt.
Torque:
9.8 N·m {100 kgf·cm, 87 in·lbf}
(e) Install the suction hose sub-assembly with the bolt.
Torque:
7.5 N·m {76 kgf·cm, 66 in·lbf}
7. INSTALL FRONT UPPER FENDER APRON SEAL
(a) Install the front upper fender apron seal with the 5 clips.
8. INSTALL GENERATOR ASSEMBLY (for 2GR-FKS)
Click here
9. INSPECT FAN AND GENERATOR V BELT (for 2TR-FE)
Click here
10. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
Torque:
5.4 N·m {55 kgf·cm, 48 in·lbf}
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected.
Click here
11. CHARGE AIR CONDITIONING SYSTEM WITH REFRIGERANT
Click here
12. WARM UP ENGINE
Click here
13. INSPECT FOR REFRIGERANT LEAK
Click here
Fuel Main Valve
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY
(See page )
2. REMOVE FUEL SENDER GAUGE ASSEMBLY
3. REMOVE NO. 1 FUEL SUB-TANK
4. REMOVE FUEL PUMP FILTER
5. REMOVE FUEL MAIN VALVE ASSEMBLY
(a) Remove t ...
Dtc Check / Clear
DTC CHECK / CLEAR
NOTICE:
When the diagnosis system is changed from normal mode to check mode or vice versa,
all DTCs and freeze frame data recorded in normal mode are cleared. Before changing
modes, always check and make a note of DTCs and freeze frame data.
HINT:
DTCs which are sto ...
Road Test
ROAD TEST
PROBLEM SYMPTOM CONFIRMATION
HINT:
The dynamic radar cruise control system has 2 cruise control modes:
constant speed control mode and vehicle-to-vehicle distance control mode.
Vehicle-to-vehicle distance control mode is selected by default when
the dyna ...