Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Installation

INSTALLATION

PROCEDURE

1. INSTALL STEERING COLUMN ASSEMBLY

(a) Install the steering column assembly with the 2 nuts and bolt.

Torque:

21 N·m {214 kgf·cm, 15 ft·lbf}

(b) Connect each of the connectors to the steering column assembly.

(c) Connect the wire harness clamps to the steering column assembly.

CAUTION:

Wipe any dirt off the installation plane and column body side.

NOTICE:

Be careful not to scratch or soil the installation plane of the steering column.

2. INSTALL NO. 2 STEERING INTERMEDIATE SHAFT

(a) Align the matchmarks on the power steering link and No. 2 steering intermediate

(a) Align the matchmarks on the power steering link and No. 2 steering intermediate shaft.

Text in Illustration

*a

Matchmark

(b) Install the No. 2 steering intermediate shaft to the power steering link with bolt C.

Torque:

35 N·m {357 kgf·cm, 26 ft·lbf}

3. INSTALL STEERING SLIDING YOKE

(a) Align the matchmarks on the steering intermediate shaft assembly and steering

(a) Align the matchmarks on the steering intermediate shaft assembly and steering sliding yoke.

Text in Illustration

*a

Matchmarks

(b) Install the steering sliding yoke to the steering intermediate shaft assembly and slide it upward.

(c) Align the matchmarks on the No. 2 steering intermediate shaft and steering sliding yoke.

(d) Install the steering sliding yoke to the No. 2 steering intermediate shaft with bolts A and B.

Torque:

35 N·m {357 kgf·cm, 26 ft·lbf}

4. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

(a) Install the No. 1 engine under cover sub-assembly with the 4 bolts.

Torque:

30 N·m {306 kgf·cm, 22 ft·lbf}

5. INSTALL STEERING COLUMN HOLE COVER

(a) Install the steering column hole cover with the 4 clips.

6. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY

Click here 7. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

7. INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

(a) Engage the 3 claws to install the combination switch assembly with spiral cable sub-assembly to the steering column assembly.

(b) Connect the connectors to the combination switch assembly with spiral cable sub-assembly.

8. INSTALL UPPER STEERING COLUMN COVER

(a) Engage the claw to install the upper steering column cover.

9. INSTALL LOWER STEERING COLUMN COVER

(a) Engage the 2 claws to install the lower steering column cover.

(b) Install the lower steering column cover with the 2 screws.

(c) Engage the claw.

10. PLACE FRONT WHEELS FACING STRAIGHT AHEAD

11. ADJUST SPIRAL CABLE

Click here 12. INSTALL STEERING WHEEL ASSEMBLY

12. INSTALL STEERING WHEEL ASSEMBLY

(a) Align the matchmarks on the steering wheel assembly and steering main shaft assembly.

(b) Install the steering wheel assembly set nut.

Torque:

50 N·m {510 kgf·cm, 37 ft·lbf}

13. INSPECT STEERING WHEEL CENTER POINT

14. INSTALL STEERING PAD

Click here 15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

15. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

Torque:

5.4 N·m {55 kgf·cm, 48 in·lbf}

NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

Click here 16. INSPECT SRS WARNING LIGHT

16. INSPECT SRS WARNING LIGHT

Click here Reassembly

Removal
REMOVAL CAUTION / NOTICE / HINT CAUTION: Some of these service operations affect the SRS. Read the precautionary notices concerning the SRS before servicing. Click here PROCEDURE 1. PRECAUTI ...

Reassembly
REASSEMBLY PROCEDURE 1. INSTALL UN-LOCK WARNING SWITCH ASSEMBLY (w/o Smart Key System) (a) Engage the 2 claws to install the un-lock warning switch assembly to the upper steering column bracket a ...

Other materials:

Check Bus 5 Lines for Short Circuit
DESCRIPTION There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 15 (CA5H) and 16 (CA5L) of the central gateway ECU (network gateway ECU) is below 54 Ω. Detection Item Trouble Area Resi ...

System Description
SYSTEM DESCRIPTION 1. POWER DOOR LOCK CONTROL SYSTEM DESCRIPTION (a) The power door lock system locks/unlocks all the doors. The main body ECU (multiplex network body ECU) receives lock/unlock request signals from a door control switch or the driver door key lock and unlock switch. Then, the ...

Seat Position Sensor
Components COMPONENTS ILLUSTRATION On-vehicle Inspection ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT SEAT POSITION AIRBAG SENSOR (for Vehicle not Involved in Collision) (a) Perform a diagnostic system check (See page ). 2. INSPECT SEAT POSITION AIRBAG SENSOR (for Vehicle Involved in C ...

© 2011-2024 Copyright www.ttguide.net