INSTALLATION
PROCEDURE
1. INSTALL OIL COOLER TUBE
(a) Install the oil cooler tube to the vehicle body with the 2 bolts.
Torque:
28 N·m {286 kgf·cm, 21 ft·lbf}
2. INSTALL NO. 4 OIL COOLER INLET HOSE AND NO. 4 OIL COOLER OUTLET HOSE
NOTICE:
(a) Install the No. 4 oil cooler inlet hose and No. 4 oil cooler outlet hose to the radiator assembly, and slide the 2 clips to secure them.
NOTICE:
Make sure to install any hose clips without a specific installation direction in a direction that does not interfere with other parts.
(b) Connect the No. 4 oil cooler inlet hose and No. 4 oil cooler outlet hose to the oil cooler tube, and slide the 2 clips to secure them.
NOTICE:
Make sure to install any hose clips without a specific installation direction in a direction that does not interfere with other parts.
(c) Then pass the No. 4 oil cooler inlet hose and No. 4 oil cooler outlet hose through the clamp and close the clamp.
3. INSTALL NO. 1 OIL COOLER INLET HOSE AND NO. 1 OIL COOLER OUTLET HOSE
NOTICE:
(a) Install the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose to the oil cooler tube, and slide the 2 clips to secure them.
NOTICE:
Make sure to install any hose clips without a specific installation direction in a direction that does not interfere with other parts.
4. INSTALL NO. 1 OIL COOLER INLET TUBE AND NO. 1 OIL COOLER OUTLET TUBE
NOTICE:
(a) Install the 2 oil cooler tube clamps to the engine assembly with the 2 bolts.
Text in Illustration
*1 |
Flexible Hose Clamp |
*2 |
Oil Cooler Tube Clamp |
Torque:
for Bolt A :
14 N·m {143 kgf·cm, 10 ft·lbf}
for Bolt B :
28 N·m {286 kgf·cm, 21 ft·lbf}
(b) Connect the ends of the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube to the automatic transmission assembly by hand.
(c) Close the 2 oil cooler tube clamps and install the 2 bolts.
Torque:
5.5 N·m {56 kgf·cm, 49 in·lbf}
(d) Install the flexible hose clamp to the automatic transmission assembly with the bolt.
Torque:
14 N·m {143 kgf·cm, 10 ft·lbf}
(e) Connect the No. 1 oil cooler inlet hose and No. 1 oil cooler outlet hose to the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube, and slide the 2 clips to secure them.
(f) Using a 17 mm union nut wrench, tighten the No. 1 oil cooler inlet tube and No. 1 oil cooler outlet tube. Text in Illustration
Torque: Specified tightening torque : 34 N·m {350 kgf·cm, 25 ft·lbf} HINT:
|
|
5. INSTALL FRONT EXHAUST PIPE ASSEMBLY
(See page )
6. ADD AUTOMATIC TRANSMISSION FLUID
(See page )
7. INSPECT FOR AUTOMATIC TRANSMISSION FLUID LEAK
8. INSTALL NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY
Torque:
30 N·m {306 kgf·cm, 22 ft·lbf}
Seatback table
Front passenger’s seatback can be used as a temporary table only when the
vehicle is stopped.
Fold down the front passenger’s seat to use the seatback table.
CAUTION
■Caution while driving
Observe the following precautions to avoid death or serious injury.
●Do not set up the ...
Rear Left Sensor Malfunction (C1AE6)
DESCRIPTION
The No. 1 ultrasonic sensor (rear corner sensor LH) is installed on the rear
bumper. The ECU detects obstacles based on signals received from the No. 1 ultrasonic
sensor (rear corner sensor LH). If the No. 1 ultrasonic sensor (rear corner sensor
LH) has an open circuit or other ma ...
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
NOTICE:
When removing any parts, turn the ignition switch off.
HINT:
If no abnormality is found when inspecting parts, check the skid control
ECU and check for poor contact at ground points.
When 2 or more DTCs are detected, perform each circuit insp ...