INSPECTION
PROCEDURE
1. INSPECT OUTER MIRROR LH
(a) Check the outer mirror heater operation. Text in Illustration
(1) Measure the resistance according to the value(s) in the table below. Standard Resistance:
If the result is not as specified, replace the outer mirror LH. |
|
(b) Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor) Text in Illustration
(1) Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on. NOTICE: Do not apply a voltage of more than 6 V. HINT: Connect 4 new 1.5 V dry-cell batteries in series. OK:
If the result is not as specified, replace the outer mirror LH. |
|
2. INSPECT OUTER MIRROR RH
(a) Check the outer mirror heater operation. Text in Illustration
(1) Measure the resistance according to the value(s) in the table below. Standard Resistance:
If the result is not as specified, replace the outer mirror RH. |
|
(b) Check the operation of the outer rear view mirror indicator. (w/ Blind Spot Monitor) Text in Illustration
(1) Apply 6 V battery voltage to the terminals of the connector, and check that the outer rear view mirror indicator comes on. NOTICE: Do not apply a voltage of more than 6 V. HINT: Connect 4 new 1.5 V dry-cell batteries in series. OK:
If the result is not as specified, replace the outer mirror RH. |
|
3. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY LH
(a) Check the operation of the mirror surface. Text in Illustration
(1) Apply battery voltage and check the operation of the mirror. OK:
If the result is not as specified, replace the outer rear view mirror assembly LH. |
|
(b) Check the side turn signal light assembly LH. Text in Illustration
(1) Apply battery voltage to the terminals of the connector, and check the illumination condition. OK:
If the result is not as specified, replace the outer rear view mirror assembly LH. |
|
(c) Check the operation of the mirror heater. Text in Illustration
(1) Measure the resistance according to the value(s) in the table below. Standard Resistance:
If the result is not as specified, replace the outer rear view mirror assembly LH. (2) Connect the cable from the positive (+) battery terminal to terminal 2 (+) and the negative (-) battery terminal to terminal 8 (-), and then check that the mirror becomes warm. HINT: It takes a short time for the mirror to become warm. OK: Mirror becomes warm. If the result is not as specified, replace the outer rear view mirror assembly LH. |
|
(d) Check the operation of the BSM. Text in Illustration
(1) Apply 6 V dry-cell battery voltage to the terminals of the connector, and check the illumination condition. NOTICE: Do not apply a voltage of 6 V or higher. HINT: Connect the 1.5 V 4 pieces batteries of a new series, applying a 6 V voltage of between each terminal of the connector. OK:
If the result is not as specified, replace the outer rear view mirror assembly LH. |
|
4. INSPECT OUTER REAR VIEW MIRROR ASSEMBLY RH
(a) Check the operation of the mirror surface. Text in Illustration
(1) Apply battery voltage and check the operation of the mirror. OK:
If the result is not as specified, replace the outer rear view mirror assembly RH. |
|
(b) Check the side turn signal light assembly RH. Text in Illustration
(1) Apply battery voltage to the terminals of the connector, and check the illumination condition. OK:
If the result is not as specified, replace the outer rear view mirror assembly RH. |
|
(c) Check the operation of the mirror heater. Text in Illustration
(1) Measure the resistance according to the value(s) in the table below. Standard Resistance:
If the result is not as specified, replace the outer rear view mirror assembly RH. (2) Connect the cable from the positive (+) battery terminal to terminal 2 (+) and the negative (-) battery terminal to terminal 8 (-), and then check that the mirror becomes warm. HINT: It takes a short time for the mirror to become warm. OK: Mirror becomes warm. If the result is not as specified, replace the outer rear view mirror assembly RH. |
|
(d) Check the operation of the BSM. Text in Illustration
(1) Apply 6 V dry-cell battery voltage to the terminals of the connector, and check the illumination condition. NOTICE: Do not apply a voltage of 6 V or higher. HINT: Connect the 1.5 V 4 pieces batteries of a new series, applying a 6 V voltage of between each terminal of the connector. OK:
If the result is not as specified, replace the outer rear view mirror assembly RH. |
|
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
NOTICE:
When removing any parts, turn the ignition switch off.
HINT:
If no abnormality is found when inspecting parts, check the skid control
ECU and check for poor contact at ground points.
When 2 or more DTCs are detected, perform each circuit insp ...
If the vehicle becomes stuck
Carry out the following procedures if the tires spin or the vehicle becomes
stuck in mud, dirt, or snow.
Stop the engine. Set the parking
brake and put the shift lever in P (vehicles with an automatic transmission) or
N (vehicles with a manual transmission).
Remove the mud, snow, or sand f ...
Inspection
INSPECTION
PROCEDURE
1. INSPECT GENERATOR BRUSH HOLDER ASSEMBLY
(a) Using a vernier caliper, measure the brush length.
Text in Illustration
*a
Length
Standard exposed length:
9.5 to 11.5 mm (0.374 to 0.453 in.)
Minimum ex ...