Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Initialization

INITIALIZATION

1. INITIALIZE POWER WINDOW CONTROL SYSTEM

NOTICE:

  • When a door window regulator assembly, power window regulator motor assembly, door glass or door glass run is reinstalled or replaced, the power window control system must be initialized. Functions such as the auto up and down function, jam protection function, catch protection function, remote control function, key-linked function, wireless transmitter-linked function, key-off operation function and window open warning function will not operate if initialization is not performed.
  • When performing initialization, do not perform any other procedures.
  • When performing initialization, use the power window switch of each door to initialize each door window.
  • Make sure to park the vehicle and turn off all electrical systems before performing initialization. Initialization will be canceled if the vehicle is driven during initialization.
  • Make sure not to hit, strike or vibrate the door window glass during initialization because the vehicle is learning the sliding resistance of the door window glass.
  • Make sure not to turn the ignition switch on or off during initialization.

HINT:

When the battery is replaced, it is not necessary to initialize the power window regulator motor assembly.

NOTICE:

  • If the battery has been replaced, it is not necessary to initialize the power window regulator motor assembly.
  • If initialization does not complete properly, the LIN communication system may be malfunctioning (See page ). ).

(a) Perform initialization according to the table below.

Condition of Power Window

Proceed to

Initialization procedure for when a power window regulator motor assembly has been replaced with a new one

Procedure A

  • Initialization procedure for when a power window regulator motor assembly has been removed/installed or a door glass and/or door glass run etc. have been removed/installed or replaced with new ones
  • Initialization procedure for when the window cannot fully open via a down operation (door glass remains visible)
  • Initialization procedure for when the door glass cannot fully close (erroneously operates in reverse) after initialization
  • Initialization procedure for when the door glass cannot fully open (erroneously stops) after initialization
  • Initialization procedure for when instructions to perform initialization appear in other troubleshooting flowcharts

HINT:

Use this procedure if a power window regulator motor assembly is being reused.

Procedure B

Initialize procedure for when the door glass unexpectedly operates in reverse or stops due to a change in the sliding after a fitting adjustment is made

Procedure C

(b) Procedure A

Perform registration of the door glass position (fully closed, fully open) and sliding resistance learning.

HINT:

  • *1: Even if the door glass is in the fully open condition before performing step 3, perform the down operation for 1 second or more.
  • *2: Do not stop the procedure during step 4.

(c) Procedure B

Reset the door glass position, and perform registration of the door glass position (fully closed, fully open) and sliding resistance learning.

HINT:

  • *1: If catch protection function operates during step 7, then hold the switch in the auto down position within 4 seconds.
  • *2: The door glass stopped position is the fully open position stored in the ECU.
  • *3: After performing step 7, return the switch to the neutral position once, and then perform an auto down operation.
  • *4: After completion, check that the door glass can fully close via an auto up operation.
  • If the initialization is not completed properly, the LIN communication system may have a malfunction (See page ). ).

(d) Procedure C

Perform sliding resistance learning.

HINT:

  • *1: If jam protection function operates during step 3, then hold the switch in the auto up position within 4 seconds.
  • *2: Do not stop the procedure during step 4, 5 or 6.
  • If erroneous reverse operation of the door glass continues even after performing steps 4, 5 and 6, perform the procedure again from step 3.
Customize Parameters
CUSTOMIZE PARAMETERS PROCEDURE 1. CUSTOMIZE POWER WINDOW CONTROL SYSTEM HINT: The following items can be customized. NOTICE: When the customer requests a change in a function, first make ...

Operation Check
OPERATION CHECK 1. CHECK WINDOW LOCK SWITCH HINT: Before performing the window lock switch operation check, make sure that the window lock switch is off (the switch is not pushed in). (a) Check ...

Other materials:

Dtc Check / Clear
DTC CHECK / CLEAR 1. CHECK FOR DTC HINT: When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins. (a) Connect the ...

Abbreviations Used In Manual
ABBREVIATIONS USED IN MANUAL Abbreviations Meaning ABS Anti-Lock Brake System A/C Air Conditioner AC Alternating Current ACC Accessory ACIS ...

Steering Angle Sensor Initialization Incomplete (C1439,C1445)
DESCRIPTION The skid control ECU (brake actuator assembly) acquires steering angle sensor zero point every time the ignition switch is turned ON and the vehicle is driven at 35 km/h (22 mph) or more for approximately 5 seconds. The ECU also stores the previous zero point. The steering angle ...

В© 2011-2024 Copyright www.ttguide.net