CAUTION / NOTICE / HINT
HINT:
PROCEDURE
1. |
VEHICLE BROUGHT TO WORKSHOP |
|
2. |
CUSTOMER PROBLEM ANALYSIS |
(a) Refer to the How to Troubleshoot ECU Controlled Systems in Introduction section.
Click here
|
3. |
INSPECT BATTERY VOLTAGE |
Standard voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding.
|
4. |
CONNECT TECHSTREAM TO DLC3* |
|
5. |
CHECK AND CLEAR DTCS AND FREEZE FRAME DATA* |
(a) Refer to DTC Check/Clear.
Click here
|
6. |
VISUAL INSPECTION |
|
7. |
SELECT CHECK MODE DIAGNOSIS* |
(a) Refer to Check Mode Procedure.
Click here
|
8. |
PROBLEM SYMPTOM CONFIRMATION |
(a) Refer to Road Test.
Click here
Result |
Proceed to |
---|---|
Symptom does not occur |
A |
Symptom occurs |
B |
B |
GO TO STEP 10 |
|
9. |
SYMPTOM SIMULATION |
(a) Refer to Symptom Simulation.
Click here
|
10. |
DTC CHECK* |
(a) Refer to DTC Check/Clear.
Click here
Result |
Proceed to |
---|---|
DTC is not output |
A |
DTC is output |
B |
B |
GO TO STEP 18 |
|
11. |
BASIC INSPECTION |
(a) Refer to Park/Neutral Position Switch.
Click here
(b) Refer to Shift Lever Assembly.
Click here
NG |
GO TO STEP 21 |
|
12. |
MECHANICAL SYSTEM TESTS |
(a) Refer to Mechanical System Tests.
Click here
NG |
GO TO STEP 17 |
|
13. |
HYDRAULIC TEST |
(a) Refer to Hydraulic Test.
Click here
NG |
GO TO STEP 17 |
|
14. |
MANUAL SHIFTING TEST |
(a) Refer to Manual Shifting Test.
Click here
NG |
GO TO STEP 16 |
|
15. |
PROBLEM SYMPTOMS TABLE CHAPTER 1 |
(a) Refer to Problem Symptoms Table.
Click here
NG |
GO TO STEP 19 |
|
16. |
PROBLEM SYMPTOMS TABLE CHAPTER 2 |
(a) Refer to Problem Symptoms Table.
Click here
|
17. |
COMPONENT INSPECTION |
NEXT |
GO TO STEP 21 |
18. |
DTC CHART |
(a) Refer to Diagnostic Trouble Code Chart.
Click here
|
19. |
CIRCUIT INSPECTION |
|
20. |
IDENTIFICATION OF PROBLEM |
|
21. |
REPAIR OR REPLACE |
|
22. |
CONFIRMATION TEST |
NEXT |
END |
Dtc Check / Clear
DTC CHECK / CLEAR
NOTICE:
When the diagnosis system is changed from normal mode to check mode or vice versa,
all DTCs and freeze frame data recorded in normal mode are cleared. Before changing
modes, always check and make a note of DTCs and freeze frame data.
HINT:
DTCs which are sto ...
Problem Symptoms Table
PROBLEM SYMPTOMS TABLE
HINT:
Use the table below to help determine the cause of problem symptoms.
If multiple suspected areas are listed, the potential causes of the symptoms
are listed in order of probability in the "Suspected Area" column of the
table. Check each sy ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL CLUTCH PEDAL NO.1 CUSHION
(a) Install the clutch pedal No. 1 cushion to the clutch pedal sub-assembly.
2. INSTALL CLUTCH PEDAL SHAFT COLLAR
(a) Apply MP grease to the clutch pedal shaft collar.
Text in Illustration
MP grease
(b) ...