CAUTION / NOTICE / HINT
HINT:
PROCEDURE
1. |
VEHICLE BROUGHT TO WORKSHOP |
|
2. |
CUSTOMER PROBLEM ANALYSIS |
What |
Vehicle model, system name |
When |
Date, time, occurrence frequency |
Where |
Road conditions |
Under what conditions? |
Driving conditions, weather conditions |
How did it happen? |
Problem symptoms |
|
3. |
INSPECT BATTERY VOLTAGE |
(a) Measure the battery voltage.
Standard voltage:
11 to 14 V
HINT:
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
|
4. |
CHECK CABIN |
(a) Check that condensation is not likely to occur in the cabin, and that the temperature is not high or extremely low in the cabin.
OK:
Condensation is not likely being produced and the temperature is not high or extremely low.
HINT:
NG |
SET CABIN TO APPROPRIATE TEMPERATURE |
|
5. |
CHECK NAVIGATION SYSTEM NORMAL CONDITION |
(a) Refer to Check System Normal Condition.
Click here
Result |
Proceed to |
---|---|
Symptom is not normal operation |
A |
Symptom is normal operation |
B |
B |
SYMPTOM IS NORMAL OPERATION |
|
6. |
CHECK CAN COMMUNICATION SYSTEM* |
(a) Check if CAN communication system DTCs are output.
Click here
Result |
Proceed to |
---|---|
CAN DTCs are not output. |
A |
CAN DTCs are output. |
B |
B |
GO TO CAN COMMUNICATION SYSTEM |
|
7. |
CHECK FOR DTC* |
(a) Refer to DTC Check/Clear.
Click here
Result |
Proceed to |
---|---|
DTCs are output |
A |
DTCs are not output |
B |
HINT:
If the system cannot enter diagnostic mode, inspect the AVC-LAN and all the components that connect to the AVC-LAN for short circuits and repair or replace the problem part.
Click here
B |
GO TO STEP 11 |
|
8. |
DTC CLEAR* |
(a) Refer to DTC Check/Clear.
Click here
HINT:
The present DTCs may not indicate actual malfunctions depending on the vehicle operating conditions.
|
9. |
RECHECK FOR DTC* |
(a) Refer to DTC Check/Clear.
Click here
Result |
Proceed to |
---|---|
DTCs are output |
A |
DTCs are not output |
B |
HINT:
B |
GO TO STEP 11 |
|
10. |
DIAGNOSTIC TROUBLE CODE CHART |
(a) Find the output code in Diagnostic Trouble Code Chart.
Click here
NEXT |
GO TO STEP 13 |
11. |
CHECK SD CARD |
(a) Enter the "SD Check" screen. Refer to Check SD Card in Operation Check.
Click here
NG |
REPLACE SD CARD |
|
12. |
PROBLEM SYMPTOMS TABLE |
(a) Refer to Problem Symptoms Table.
Click here
Result |
Proceed to |
---|---|
Fault is not listed in Problem Symptoms Table |
A |
Fault is listed in Problem Symptoms Table |
B |
HINT:
If the symptom does not recur and no DTCs are output, attempt to reproduce the symptoms.
Click here
B |
GO TO STEP 13 |
|
13. |
PERFORM TROUBLESHOOTING BASED ON MALFUNCTION SYMPTOM |
(a) Refer to Terminals of ECU.
Click here
|
14. |
CHECK CIRCUIT |
(a) Adjust, repair or replace as necessary.
|
15. |
RECHECK FOR DTC* |
(a) After clearing DTCs, recheck for DTCs.
|
16. |
PERFORM CONFIRMATION TEST |
NEXT |
END |
Installation
INSTALLATION
PROCEDURE
1. INSPECT PROPELLER SHAFT WITH CENTER BEARING ASSEMBLY (with Grease Fitting)
Text in Illustration
*1
Grease Fitting
-
-
*a
View A
*b
Front Side
HINT:
When replacing t ...
Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL REAR WHEEL CYLINDER CUP KIT
(a) Provisionally tighten the bleeder plug to the rear wheel brake cylinder,
and install the bleeder plug cap.
(b) Apply lithium soap base glycol grease to 2 new cylinder cups and the 2 pistons.
(c) Install the cylinder cup onto ea ...
Removal
REMOVAL
PROCEDURE
1. REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
(See page )
2. REMOVE NO. 1 RADIATOR HOSE
3. REMOVE NO. 2 RADIATOR HOSE
4. DISCONNECT RADIATOR RESERVE TANK HOSE
5. SEPARATE TRANSMISSION OIL COOLER HOSE (for Automatic Transmission)
(a) Disengage the c ...