Toyota Tacoma (2015-2018) Service Manual: How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
- Use these procedure to troubleshoot the seat belt warning system.
- *: Use the Techstream.
PROCEDURE
|
1. |
VEHICLE BROUGHT TO WORKSHOP |
|
.gif)
|
2. |
CUSTOMER PROBLEM ANALYSIS |
HINT:
- In troubleshooting, confirm that the problem symptoms have been accurately identified. Preconceptions should be discarded in order to make an accurate judgment. To clearly understand what the problem symptoms are, it is extremely important to ask the customer about the problem and the conditions at the time the malfunction occurred.
- Gather as much information as possible for reference. Past problems that seem unrelated may also help in some cases.
- The following 5 items are important points in the problem analysis:
|
What |
Vehicle, system name |
|
When |
Date, time, occurrence frequency |
|
Where |
Road conditions |
|
Under what conditions? |
Driving conditions, weather conditions |
|
How did it happen? |
Problem symptoms |
|
|
3. |
INSPECT BATTERY VOLTAGE |
(a) Measure the battery voltage.
Standard voltage:
11 to 14 V
If the voltage is below 11 V, recharge or replace the battery before proceeding to the next step.
|
|
4. |
CHECK COMMUNICATION FUNCTION OF CAN COMMUNICATION SYSTEM* |
(a) Use the Techstream to check if the CAN communication system is functioning normally.
|
Result |
Proceed to |
|---|---|
|
CAN DTC is not output |
A |
|
CAN DTC is output |
B |
| B | .gif) |
GO TO CAN COMMUNICATION SYSTEM |
|
|
5. |
CHECK FOR DTC (AIRBAG SYSTEM)* |
(a) Clear the DTC.
Click here .gif)
(b) Recheck for DTCs.
|
Result |
Proceed to |
|---|---|
|
DTC is not output |
A |
|
DTC is output |
B |
| B | |
GO TO AIRBAG SYSTEM |
|
|
6. |
CHECK FOR DTC (OCCUPANT CLASSIFICATION SYSTEM)* |
(a) Clear the DTC.
Click here
(b) Recheck for DTCs.
|
Result |
Proceed to |
|---|---|
|
DTC is not output |
A |
|
DTC is output |
B |
| B | |
GO TO OCCUPANT CLASSIFICATION SYSTEM |
|
|
7. |
PROBLEM SYMPTOMS TABLE |
(a) Refer to the Problem Symptoms Table.
Click here
|
Result |
Proceed to |
|---|---|
|
Fault is not listed in Problem Symptoms Table |
A |
|
Fault is listed in Problem Symptoms Table |
B |
| B | |
GO TO STEP 9 |
|
|
8. |
OVERALL ANALYSIS AND TROUBLESHOOTING* |
(a) Data List / Active Test.
Click here
(b) Terminals of ECU.
Click here
(c) On-vehicle Inspection.
Click here
|
|
9. |
REPAIR OR REPLACE |
|
|
10. |
CONFIRMATION TEST |
| NEXT | |
END |
Customize Parameters
CUSTOMIZE PARAMETERS
1. CUSTOMIZE FUNCTION WITH TECHSTREAM
NOTICE:
Be sure to record the current settings before customizing.
These buzzers should be ON for safe driving. Perform these ...
System Description
SYSTEM DESCRIPTION
1. SEAT BELT WARNING SYSTEM DESCRIPTION
(a) Seat belt warning light operation for driver seat belt:
The seat belt warning light on the combination meter assembly illuminates, bli ...
Other materials:
Power Source Mode does not Change to ON (IG)
DESCRIPTION
If the engine switch is pressed with the electrical key transmitter sub-assembly
in the cabin, the certification ECU (smart key ECU assembly) receives a signal and
changes the power source mode.
HINT:
When the cable is disconnected and reconnected to the negative (-) battery termi ...
Reassembly
REASSEMBLY
CAUTION / NOTICE / HINT
HINT:
The procedure described below is for the LH side. Use the same procedure for
both the LH and RH sides, unless otherwise specified.
PROCEDURE
1. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY
(a) Install the rear seat cushion frame sub-assembl ...
Switch Failure (B2342)
DESCRIPTION
This DTC is stored when the sliding roof ECU (sliding roof drive gear sub-assembly)
detects that the sliding roof switch is stuck for 30 seconds or more.
DTC No.
DTC Detection Condition
Trouble Area
B2342
Sliding roof ECU ( ...
