Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: General Information

GENERAL INFORMATION

  • A large number of ECU controlled systems are used in the TOYOTA TACOMA. In general, ECU controlled systems are considered to be very intricate, requiring a high level of technical knowledge to troubleshoot. However, most problem checking procedures only involve inspecting the ECU controlled system's circuits one by one. An adequate understanding of the system and a basic knowledge of electricity is enough to perform effective troubleshooting, accurate diagnoses and necessary repairs.

1. TROUBLESHOOTING PROCEDURES

  • The troubleshooting procedures consist of diagnosis procedures for when a DTC is stored and diagnosis procedures for when no DTC is stored. The basic idea is explained in the following table.

    Procedure Type

    Details

    Troubleshooting Method

    DTC Based Diagnosis

    The diagnosis procedure is based on the DTC that is stored.

    The malfunctioning part is identified based on the DTC detection conditions using a process of elimination.

    The possible trouble areas are eliminated one-by-one by use of the Techstream and inspection of related parts.

    Symptom Based Diagnosis

    (No DTCs stored)

    The diagnosis procedure is based on problem symptoms.

    The malfunctioning part is identified based on the problem symptoms using a process of elimination.

    The possible trouble areas are eliminated one-by-one by use of the Techstream and inspection of related parts.

  • Vehicle systems are complex and use many ECUs that are difficult to inspect independently. Therefore, a process of elimination is used, where components that can be inspected individually are inspected, and if no problems are found in these components, the related ECU is identified as the problem and replaced.
  • It is extremely important to ask the customer about the environment and the conditions present when the problem occurred (Customer Problem Analysis). This makes it possible to simulate the conditions and confirm the symptom. If the symptom cannot be confirmed or the DTC does not recur, the malfunctioning part may not be identified using the troubleshooting procedure, and the ECU for the related system may be replaced even though it is not defective. If this happens, the original problem will not be solved.
  • In order to prevent endless expansion of troubleshooting procedures, the troubleshooting procedures are written with the assumption that multiple malfunctions do not occur simultaneously for a single problem symptom.
  • To identify the malfunctioning part, troubleshooting procedures narrow down the target by separating components, ECUs and wire harnesses during the inspection. If the wire harness is identified as the cause of the problem, it is necessary to inspect not only the connections to components and ECUs but also all of the wire harness connectors between the component and the ECU.
  • FOR USING TECHSTREAM
    • Connect the cable of the Techstream (with CAN VIM) to the DLC3, turn the ignition switch ON and attempt to use the tester. If the display indicates that a communication error has occurred, there is a problem either with the vehicle or with the tester.
      • If communication is normal when the tester is connected to another vehicle, inspect the DLC3 of the original vehicle.
      • If communication is still not possible when the tester is connected to another vehicle, the problem may be in the tester itself. Consult the Service Department listed in the tester's instruction manual.
How To Troubleshoot Ecu Controlled Systems
...

How To Proceed With Troubleshooting
HOW TO PROCEED WITH TROUBLESHOOTING 1. OPERATION FLOW HINT: Perform troubleshooting in accordance with the procedures below. The following is an outline of basic troubleshooting procedures. Confi ...

Other materials:

Heater Circuit (C1AAE)
DESCRIPTION The forward recognition camera controls the current supplied to the camera heater (forward recognition hood). If the forward recognition camera detects a malfunction in the camera heater (forward recognition hood) circuit, DTC C1AAE is stored. DTC No. Detecti ...

Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Smart Key System DTC Code Detection Item See page B27A1 Open in Driver Side Electrical Antenna Circuit B27A5 Open in Front Floor Electrical Key Oscillator Circuit ...

Removal
REMOVAL PROCEDURE 1. REMOVE CLUTCH MASTER CYLINDER ASSEMBLY (See page ) 2. REMOVE TURN OVER SPRING SEAT COMPRESSION SPRING (a) Remove the compression spring. 3. REMOVE CLUTCH PEDAL SUB-ASSEMBLY (a) Remove the bolt and nut. ...

В© 2011-2024 Copyright www.ttguide.net