Toyota Tacoma (2015-2018) Service Manual: Front Speed Sensor RH Performance (C1409,C1410)

Toyota Tacoma (2015-2018) Service Manual / Brake Control / Dynamic Control Systems / Vehicle Stability Control System(for Hydraulic Brake Booster) / Front Speed Sensor RH Performance (C1409,C1410)

DESCRIPTION

Refer to DTCs C1401 and C1402 (See page ).

DTC Code	DTC Detection Condition	Trouble Area
C1409 C1410	One of the following conditions is met: When the vehicle is driven in reverse at a speed of 3 km/h (2 mph) or more and 3 of the wheel sensors detect the reverse signal, the other sensor detects a high frequency pulse 75 times while the ignition switch is ON. At a vehicle speed of 10 km/h (6 mph) or more, the vehicle speed sensor output drops by 50% for 5 seconds. The lowest wheel speed is 10 km/h (6 mph) or more and the difference between the highest and lowest wheel speed values is 2 km/h (1 mph) or less for 15 seconds. At a vehicle speed of 30 km/h (19 mph) or more, one wheel direction is different from the other 3 wheels for 1 second. At a vehicle speed of 100 km/h (62 mph), a reverse signal is output for 1 second or more. At a vehicle speed of 30 km/h (19 mph) or more, the rotation direction of one of the wheels is not detected normally and the rotation direction of the other 3 wheels is not the same for 1 second.	Front speed sensor RH/LH

DTC Code

DTC Detection Condition

Trouble Area

C1409

C1410

One of the following conditions is met:

When the vehicle is driven in reverse at a speed of 3 km/h (2 mph) or more and 3 of the wheel sensors detect the reverse signal, the other sensor detects a high frequency pulse 75 times while the ignition switch is ON.
At a vehicle speed of 10 km/h (6 mph) or more, the vehicle speed sensor output drops by 50% for 5 seconds.
The lowest wheel speed is 10 km/h (6 mph) or more and the difference between the highest and lowest wheel speed values is 2 km/h (1 mph) or less for 15 seconds.
At a vehicle speed of 30 km/h (19 mph) or more, one wheel direction is different from the other 3 wheels for 1 second.
At a vehicle speed of 100 km/h (62 mph), a reverse signal is output for 1 second or more.
At a vehicle speed of 30 km/h (19 mph) or more, the rotation direction of one of the wheels is not detected normally and the rotation direction of the other 3 wheels is not the same for 1 second.

Front speed sensor RH/LH

HINT:

DTC C1409 is for the front speed sensor RH.
DTC C1410 is for the front speed sensor LH.

CAUTION / NOTICE / HINT

NOTICE:

Check the speed sensor signal after replacement (See page PROCEDURE ).

PROCEDURE

1.	REPLACE FRONT SPEED SENSOR

(a) Replace the front speed sensor (See page ).

END

Open or Short in Rear Speed Sensor RH Circuit (C1407,C1408)

DESCRIPTION Refer to DTCs C1401 and C1402 (See page ). DTC Code DTC Detection Condition Trouble Area C1407 C1408 Either condition is ...

Rear Speed Sensor RH Performance (C1411,C1412)

DESCRIPTION Refer to DTCs C1401 and C1402 (See page ). DTC Code DTC Detection Condition Trouble Area C1411 C1412 One of the following ...

Other materials:

Parking Brake Switch Circuit
DESCRIPTION This circuit is from the parking brake switch assembly to the radio and display receiver assembly. WIRING DIAGRAM PROCEDURE 1. CHECK VEHICLE SIGNAL (a) Display the "Vehicle Signal Check Mode" screen (See page ). ...

ACC Signal Circuit
DESCRIPTION This circuit detects whether the ignition switch is ACC or off, and sends this information to the main body ECU (multiplex network body ECU). WIRING DIAGRAM CAUTION / NOTICE / HINT NOTICE: Inspect the fuses for circuits related to this system before performing the fo ...

Customize Parameters
CUSTOMIZE PARAMETERS PROCEDURE 1. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) HINT: The following items can be customized. NOTICE: When the customer requests a change in a function, first make sure that the function can be customized. Record the current settings before cus ...