DESCRIPTION
Output to the front seat cushion heater assembly RH temperature sensor stops if one of the following occurs: 1) the temperature sensor is open or shorted; or 2) the temperature sensor is damaged and its output value does not change.
DTC Code |
DTC Detection Condition |
Trouble Area |
---|---|---|
B14C0 |
Seat heater temperature sensor malfunction |
|
WIRING DIAGRAM
PROCEDURE
1. |
CLEAR DTC |
(a) Clear the DTCs (See page ).
|
2. |
CHECK FOR DTC |
(a) Check for DTCs (See page ).
OK:
DTC B14C0 is not output.
OK |
USE SIMULATION METHOD TO CHECK |
|
3. |
READ VALUE USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Air Conditioner / Data List.
(e) Check the value(s) by referring to the table below.
Air Conditioner:
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
FR Seat Heater Temperature |
Front seat RH side seat heater temperature / min: -29.7°C or max: 59.55°C |
Within range from 36 to 42.2°C (96 to 108°F) |
Front seat heater is on |
OK:
The display is as specified in the normal condition column.
Result
Result |
Proceed to |
---|---|
NG |
A |
OK |
B |
B |
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |
|
4. |
INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY RH |
(a) Remove the front seat cushion heater assembly RH (See page ).
(b) Inspect the front seat cushion heater assembly RH (See page ).
NG |
REPLACE FRONT SEAT CUSHION HEATER ASSEMBLY RH |
|
5. |
CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - FRONT SEAT CUSHION HEATER ASSEMBLY RH) |
(a) Disconnect the A35 and A36 air conditioning amplifier assembly connector.
(b) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
A36-31 (TSR) - S41-2 (TH) |
Always |
Below 1 Ω |
A35-15 (SG-2) - S41-6 (E) |
Always |
Below 1 Ω |
A36-31 (TSR) - Body ground |
Always |
10 kΩ or higher |
A35-15 (SG-2)) - Body ground |
Always |
10 kΩ or higher |
OK |
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
Dtc Check / Clear
DTC CHECK / CLEAR
1. CHECK DTC
(a) Check the DTCs.
(1) Turn the ignition switch off.
(2) Connect the Techstream to the DLC3.
(3) Turn the ignition switch to ON.
(4) Turn the Techstream on.
(5) Read the DTCs following the prompts on the Techstream screen. Enter the following
menus: Powertrai ...
Starting System
Parts Location
PARTS LOCATION
ILLUSTRATION
ILLUSTRATION
Precaution
PRECAUTION
1. IGNITION SWITCH EXPRESSIONS
(a) The type of ignition switch used on this model differs depending on the specifications
of the vehicle. The expressions listed in the table below are used in this section. ...
Terminals Of Ecu
TERMINALS OF ECU
1. BLIND SPOT MONITOR SENSOR LH (MASTER)
Terminal No.
(Symbol)
Wiring Color
Terminal Description
Condition
Specified Condition
B12-3 (BIND) - B12-10 (BLGD)
Y - W-B
Blind spot monitor ...