Toyota Tacoma manuals

Toyota Tacoma 2015-2018 Service Manual: Front Passenger Side Seat Heater does not Operate

Toyota Tacoma 2015-2018 Service Manual / Seat / Seat Heater System / Front Passenger Side Seat Heater does not Operate

DESCRIPTION

When the seat heater switch on the air conditioning control assembly is operated, the air conditioning amplifier assembly receives the signal. The air conditioning amplifier assembly receives the signal and operates the front seat heater.

WIRING DIAGRAM

CAUTION / NOTICE / HINT

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.

PROCEDURE

1.

READ VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch ON.

(c) Turn the Techstream on.

(d) Enter the following menus: Body Electrical / Air Conditioner / Data List.

(e) Check the value(s) by referring to the table below.

Air Conditioner:

Tester Display

Measurement Item/Range

Normal Condition

Diagnostic Note

FR Seat Heater Temperature

Front seat RH side seat heater temperature / min: -29.7°C or max: 59.55°C

Within range from 36 to 43°C (96 to 109°F)

Front seat heater is on

OK:

The display is as specified in the normal condition column.

Result

Result

Proceed to

NG

A

OK

B

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

A

2.

CHECK HARNESS AND CONNECTOR (BATTERY - FRONT SEAT CUSHION HEATER ASSEMBLY RH - BODY GROUND)

(a) Disconnect the S41 front seat cushion heater assembly RH connector.

(b) Measure the voltage and resistance according to the value(s) in the table below.

Standard Voltage:

Tester Connection

Switch Condition

Specified Condition

S41-3 (B1) - Body ground

Ignition switch ON

11 to 14 V

Standard Resistance:

Tester Connection

Condition

Specified Condition

S41-5 (E) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

3.

INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY RH

(a) Remove the front seat cushion heater assembly RH (See page ). ). (b) Inspect the front seat cushion heater assembly RH (See page ).

(b) Inspect the front seat cushion heater assembly RH (See page ).

NG

REPLACE FRONT SEAT CUSHION HEATER ASSEMBLY RH

OK

4.

INSPECT FRONT SEATBACK HEATER ASSEMBLY RH

(a) Remove the front seatback heater assembly RH (See page (b) Inspect the front seatback heater assembly RH (See page ).

(b) Inspect the front seatback heater assembly RH (See page ).

NG

REPLACE FRONT SEATBACK HEATER ASSEMBLY RH

OK

5.

CHECK FRONT SEAT CUSHION HEATER ASSEMBLY RH

(a) Temporarily replace the front seat cushion heater assembly RH with a new or known good one (See page ). (b) Check that the seat heater system is operated normally. (b) Check that the seat heater system is operated normally. ).

(b) Check that the seat heater system is operated normally.

OK:

The seat heater system is operated normally.

Result

Result

Proceed to

NG

A

OK

B

B

END (FRONT SEAT CUSHION HEATER ASSEMBLY RH WAS DEFECTIVE)

A

6.

CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - FRONT SEAT CUSHION HEATER ASSEMBLY RH)

(a) Disconnect the A35 and A36 air conditioning amplifier assembly connector.

(b) Disconnect the S41 front seat cushion heater assembly RH connector.

(c) Measure the resistance according to the value(s) in the table below.

Standard Resistance:

Tester Connection

Condition

Specified Condition

A35-24 (SHP+) - S41-1 (B)

Always

Below 1 Ω

A36-31 (TSR) - S41-2 (TH)

Always

Below 1 Ω

A35-15 (SG-2) - S41-6 (E)

Always

Below 1 Ω

A35-24 (SHP+) or S41-1 (B) - Body ground

Always

10 kΩ or higher

A36-31 (TSR) or S41-2 (TH) - Body ground

Always

10 kΩ or higher

A35-15 (SG-2) or S41-6 (E) - Body ground

Always

10 kΩ or higher

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK

7.

CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

(a) Temporarily replace the air conditioning amplifier assembly with a new or known good one (See page (b) Check that the seat heater system is operated normally. ).

(b) Check that the seat heater system is operated normally.

OK:

The seat heater system is operated normally.

Result

Result

Proceed to

NG

A

OK

B

A

END (AIR CONDITIONING AMPLIFIER ASSEMBLY WAS DEFECTIVE)

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

Driver Side Seat Heater does not Operate
DESCRIPTION When the seat heater switch on the air conditioning control assembly is operated, the air conditioning amplifier assembly receives the signal. The air conditioning amplifier assembly ...

Seat Belt
...

Other materials:

Fail-safe Chart
FAIL-SAFE CHART FAIL-SAFE FUNCTION (a) When a malfunction occurs in the lane departure alert system, a message will be displayed on the multi-information display in the combination meter assembly and the lane departure alert system will be disabled depending on the malfunction. War ...

Removal
REMOVAL PROCEDURE 1. REMOVE REAR WHEEL 2. DRAIN BRAKE FLUID HINT: Immediately wash off any brake fluid that comes into contact with any painted surfaces. 3. REMOVE REAR BRAKE DRUM SUB-ASSEMBLY (a) Release the parking brake, and remove the rear brake drum. If the rear brake drum cannot be ...

Clutch Switch Circuit
DESCRIPTION While depressing the clutch pedal, the clutch start switch assembly sends a signal to terminal MTN of the 4 wheel drive control ECU. While the signal is input, switching between H4 and L4 is possible. WIRING DIAGRAM PROCEDURE 1. READ VALUE USING TECHSTREA ...

© 2011-2022 Copyright www.ttguide.net