FAIL-SAFE CHART
HINT:
If any of the following auto cancel conditions are detected while the dynamic radar cruise control system is controlling vehicle speed, the system clears the stored vehicle speed and cancels control of vehicle speed by the dynamic radar cruise control system.
Automatic Cancel Control
Constant Speed Control Mode:
Auto Cancel Condition |
Warning |
Fail-safe Deactivation Condition |
|||
---|---|---|---|---|---|
Multi-information Display |
Master Warning Light |
Cruise Control Indicator |
Warning Buzzer |
||
Open or short in stop light switch circuit |
Cruise Control Malfunction Visit Your Dealer |
Illuminates |
Does not illuminate |
Sounds |
Dynamic radar cruise control system is turned off and back on again using the cruise control main switch (ON-OFF button). |
|
Cruise Control Malfunction Visit Your Dealer |
Illuminates |
Does not illuminate |
Sounds |
Ignition switch ON again. |
If the following condition occurs, the ECM cancels control of vehicle speed by the dynamic radar cruise control system (stored vehicle speed is maintained):
|
- |
Does not illuminate |
Illuminates |
- |
Cruise control main switch is pushed to +RES |
Malfunction in SFI system |
- |
Illuminates |
Does not illuminate |
- |
Dynamic radar cruise control system is turned off and back on again using the cruise control main switch (ON-OFF button). |
Vehicle speed is less than stored vehicle speed by approximately 16 km/h (10 mph) or more |
- |
Does not illuminate |
Illuminates |
- |
Cruise control main switch is pushed to -SET |
|
- |
Does not illuminate |
Illuminates |
- |
Cruise control main switch is pushed to +RES |
Auto Cancel Condition |
Warning |
Fail-safe Deactivation Condition |
|||
---|---|---|---|---|---|
Multi-information Display |
Master Warning Light |
Cruise Control Indicator |
Warning Buzzer |
||
Open or short in stop light switch circuit |
Cruise Control Malfunction Visit Your Dealer |
Illuminates |
Does not illuminate |
Sounds |
Dynamic radar cruise control system is turned off and back on again using the cruise control main switch (ON-OFF button). |
Malfunction in SFI system |
- |
Illuminates |
Does not illuminate |
- |
Dynamic radar cruise control system is turned off and back on again using the cruise control main switch (ON-OFF button). |
If either of the following conditions occurs, the ECM cancels control of vehicle speed by the dynamic radar cruise control system (stored vehicle speed is maintained):
|
- |
Does not illuminate |
Illuminates |
Sounds |
Cruise control main switch is pushed to +RES |
|
Cruise Control Malfunction Visit Your Dealer |
Illuminates |
Does not illuminate |
Sounds |
Ignition switch ON again. |
If the following condition occurs, the ECM cancels control of vehicle speed by the dynamic radar cruise control system (stored vehicle speed is maintained):
|
Radar Cruise Control Unavailable Clean Sensor |
Illuminates |
Does not illuminate |
Sounds |
The condition returns to normal (the resume function can be operated after fail-safe is deactivated). |
If any of the conditions listed below occurs, the ECM cancels control of vehicle speed by the dynamic radar cruise control system (stored vehicle speed is maintained):
|
Radar Cruise Control Unavailable |
Illuminates |
Does not illuminate |
Sounds |
The conditions return to normal (the resume function can be operated after fail-safe is deactivated). |
|
- |
Does not illuminate |
Illuminates |
- |
Cruise control main switch is pushed to +RES |
Inspection
INSPECTION
PROCEDURE
1. INSPECT BRAKE VACUUM CHECK VALVE ASSEMBLY
(a) Check that there is ventilation from the booster to the engine, and
no ventilation from the engine to the booster.
If the results are not as specified, replace the vacuum check valve.
...
VSC OFF Indicator Light Remains ON
DESCRIPTION
In 2WD mode:
Operation of the VSC OFF switch changes the vehicle between normal mode,
TRAC OFF mode (AUTO LSD mode) and VSC OFF mode. During normal mode, pressing
the VSC OFF switch for a short amount of time changes the vehicle to TRAC
OFF mode (AUTO LSD mode), TR ...
Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL FRONT PROPELLER SHAFT UNIVERSAL JOINT SPIDER BEARING
(a) Apply MP grease to a new spider and spider bearing.
(b) Fit the spider into the flange yoke.
(c) Measure dimension A between the snap ring grooves.
...