Toyota Tacoma (2015-2018) Service Manual: Driver Side Seat Heater does not Operate
DESCRIPTION
When the seat heater switch on the air conditioning control assembly is operated, the air conditioning amplifier assembly receives the signal. The air conditioning amplifier assembly receives the signal and operates the front seat heater.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.
PROCEDURE
|
1. |
READ VALUE USING TECHSTREAM |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Air Conditioner / Data List.
(e) Check the value(s) by referring to the table below.
Air Conditioner:
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
FL Seat Heater Temperature |
Front seat LH side seat heater temperature / min: -29.7°C or max: 59.55°C |
Within range from 36 to 43°C (96 to 109°F) |
Front seat heater is on |
OK:
The display is as specified in the normal condition column.
Result|
Result |
Proceed to |
|---|---|
|
NG |
A |
|
OK |
B |
| B | .gif) |
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |
|
.gif)
|
2. |
CHECK HARNESS AND CONNECTOR (BATTERY - FRONT SEAT CUSHION HEATER ASSEMBLY LH - BODY GROUND) |
(a) Disconnect the S40 front seat cushion heater assembly LH connector.
(b) Measure the voltage and resistance according to the value(s) in the table below.
Standard Voltage:
|
Tester Connection |
Switch Condition |
Specified Condition |
|---|---|---|
|
S40-3 (B) - Body ground |
Ignition switch ON |
11 to 14 V |
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
S40-5 (E) - Body ground |
Always |
Below 1 Ω |
| NG | |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
3. |
INSPECT FRONT SEAT CUSHION HEATER ASSEMBLY LH |
(a) Remove the front seat cushion heater assembly LH (See page
.gif)
).
(b) Inspect the front seat cushion heater assembly LH (See page
).
| NG | |
REPLACE FRONT SEAT CUSHION HEATER ASSEMBLY LH |
|
|
4. |
INSPECT FRONT SEATBACK HEATER ASSEMBLY LH |
(a) Remove the front seatback heater assembly LH (See page
).
(b) Inspect the front seatback heater assembly LH (See page
).
| NG | |
REPLACE FRONT SEATBACK HEATER ASSEMBLY LH |
|
|
5. |
CHECK FRONT SEAT CUSHION HEATER ASSEMBLY LH |
(a) Temporarily replace the front seat cushion heater assembly LH with a new
or known good one (See page
).
(b) Check that the seat heater system is operated normally.
OK:
The seat heater system is operated normally.
Result|
Result |
Proceed to |
|---|---|
|
NG |
A |
|
OK |
B |
| B | |
END (FRONT SEAT CUSHION HEATER ASSEMBLY LH WAS DEFECTIVE) |
|
|
6. |
CHECK HARNESS AND CONNECTOR (AIR CONDITIONING AMPLIFIER ASSEMBLY - FRONT SEAT CUSHION HEATER ASSEMBLY LH) |
(a) Disconnect the A35 and A36 air conditioning amplifier assembly connector.
(b) Disconnect the S40 front seat cushion heater assembly LH connector.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
|
Tester Connection |
Condition |
Specified Condition |
|---|---|---|
|
A35-23 (SHD+) - S40-1 (B) |
Always |
Below 1 Ω |
|
A36-32 (TSL) - S40-2 (TH) |
Always |
Below 1 Ω |
|
A35-15 (SG-2) - S40-6 (E) |
Always |
Below 1 Ω |
|
A35-23 (SHD+) or S40-1 (B) |
Always |
10 kΩ or higher |
|
A36-32 (TSL) or S40-2 (TH) |
Always |
10 kΩ or higher |
|
A35-15 (SG-2) or S40-6 (E) |
Always |
10 kΩ or higher |
| NG | |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
7. |
CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY |
(a) Temporarily replace the air conditioning amplifier assembly with a new or
known good one (See page ).
(b) Check that the seat heater system is operated normally.
OK:
The seat heater system is operated normally.
Result|
Result |
Proceed to |
|---|---|
|
NG |
A |
|
OK |
B |
| A | |
END (AIR CONDITIONING AMPLIFIER ASSEMBLY WAS DEFECTIVE) |
| B | |
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY |
Front Left Seat Heat Sensor Circuit (B14C1)
DESCRIPTION
Output to the front seat cushion heater assembly LH temperature sensor stops
if one of the following occurs: 1) the temperature sensor is open or shorted; or
2) the temperature sensor ...
Front Passenger Side Seat Heater does not Operate
DESCRIPTION
When the seat heater switch on the air conditioning control assembly is operated,
the air conditioning amplifier assembly receives the signal. The air conditioning
amplifier assembly ...
Other materials:
Precaution
PRECAUTION
1. HANDLING PRECAUTIONS FOR STEERING SYSTEM
(a) Care must be taken when replacing parts. Incorrect replacement could affect
the performance of the steering system and result in driving hazards.
2. HANDLING PRECAUTIONS FOR SRS AIRBAG SYSTEM
(a) The vehicle is equipped with SRS (Suppl ...
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT DRIVER SEAT BELT WARNING LIGHT
HINT:
The seat belt warning light on the combination meter assembly is used for both
the driver seat and front passenger seat.
(a) Turn the ignition switch to ON.
(b) When the driver seat belt is not fastened, check th ...
Hydraulic Test
HYDRAULIC TEST
1. PERFORM HYDRAULIC TEST
(a) Measure the line pressure.
CAUTION:
The line pressure test should always be performed with at least 2 people. One
person should observe the condition of the wheels and wheel chocks while the other
is performing the test.
NOTICE:
Perform ...
