Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Disposal

DISPOSAL

CAUTION / NOTICE / HINT

CAUTION:

Before performing pre-disposal deployment of any SRS part, review and closely follow all applicable environmental and hazardous material regulations. Pre-disposal deployment may be considered hazardous material treatment.

PROCEDURE

1. PRECAUTION

CAUTION:

  • An airbag or pretensioner may be activated by static electricity. To prevent this, be sure to touch a metal surface with your bare hands to discharge static electricity before performing this procedure.
  • Never dispose of a curtain shield airbag assembly with an undeployed airbag.
  • The airbag produces an exploding sound when it is deployed, so perform the operation outdoors and where it will not create a nuisance to nearby residents.
  • When deploying the airbag, always use the specified SST (SRS Airbag Deployment Tool). Perform the operation in a place away from electrical noise.
  • When deploying the airbag, perform the operation at least 10 m (32.8 ft.) away from the curtain shield airbag assembly.
  • The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
  • Use gloves and safety glasses when handling a curtain shield airbag assembly with a deployed airbag.
  • Do not apply water etc. to a curtain shield airbag assembly with a deployed airbag.
  • Always wash your hands with water after completing the operation.

HINT:

When scrapping a vehicle equipped with the SRS or disposing of the curtain shield airbag assembly, be sure to deploy the airbag first in accordance with the procedure described below. If any abnormality occurs with the airbag deployment, contact the SERVICE DEPT. of TOYOTA MOTOR SALES, U.S.A., INC.

2. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When Installed in Vehicle)

NOTICE:

  • When disposing of the curtain shield airbag assembly, never use the customer's vehicle to deploy the airbag.
  • Be sure to observe the following procedure when deploying the airbag.

HINT:

Prepare a battery as the power source to deploy the airbag.

(a) Check the function of the SST (See page ). ).

(b) Precaution (See page (c) Disconnect the cable from the negative battery terminal. ).

(c) Disconnect the cable from the negative battery terminal.

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

(d) Remove the roof headlining assembly (See page (e) Install SST. (e) Install SST. ).

(e) Install SST.

(1) Using a screwdriver with its tip wrapped in protective tape, release the airbag connector lock.

Text in Illustration

*a

Protective Tape

(2) Disconnect the connector from the curtain shield airbag assembly.

NOTICE:

When handling the airbag connector, take care not to damage the airbag wire harness.

(3) After connecting SST to each other, connect them to the curtain shield airbag.

SST: 09082-00700

SST: 09082-00802

09082-10801

09082-20801

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock.

(4) Move SST at least 10 m (32.8 ft.) away from the front side window of the vehicle.

Text in Illustration

*a

Battery

*b

10 m (32.8 ft.) or more

(5) While maintaining sufficient clearance for the SST wire harness in the front side window, close all doors and windows of the vehicle.

NOTICE:

Take care not to damage the SST wire harness.

(6) Connect the red clip of SST to the positive (+) battery terminal and the black clip of SST to the negative (-) battery terminal.

(f) Deploy the airbag.

(1) Check that no one is inside the vehicle or within a 10 m (32.8 ft.) radius of the vehicle.

(2) Press the SST activation switch and deploy the airbag.

CAUTION:

  • Before deployment, make sure that no one is near the vehicle.
  • The curtain shield airbag assembly becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
  • Use gloves and safety glasses when handling a curtain shield airbag assembly with a deployed airbag.
  • Do not apply water etc. to a curtain shield airbag assembly with a deployed airbag.
  • Always wash your hands with water after completing the operation.

HINT:

The airbag is deployed as the LED of the SST activation switch comes on.

3. DISPOSE OF CURTAIN SHIELD AIRBAG ASSEMBLY (When Not Installed in Vehicle)

NOTICE:

Be sure to follow the procedure detailed below when deploying the airbag.

HINT:

Prepare a battery as the power source to deploy the airbag.

(a) Check the function of the SST (See page ).

(b) Remove the curtain shield airbag assembly (See page CAUTION: CAUTION: ).

CAUTION:

Before removing the curtain shield airbag assembly, wait at least 90 seconds after turning the ignition switch off and disconnecting the cable from the negative (-) battery terminal.

(c) Cut off the deployment section of the curtain shield airbag assembly.

(d) Using a service-purpose wire harness for the vehicle, tie the curtain shield airbag assembly to the tire.

Text in Illustration

*a

Wire Diameter

*b

Stripped Wire

Wire:

Cross-sectional area of stripped wire

1.25 mm2 (0.0019 in.2) or more

CAUTION:

If the wire harness is too thin or an alternative object is used to tie down the curtain shield airbag, it may be snapped by the shock when the airbag is deployed. Always use a wire harness for vehicle use with an area of at least 1.25 mm2 (0.00193 in.2).

HINT:

HINT:

To calculate the cross-sectional area of the stripped wire section:

Area = 3.14 x (Diameter)2 / 4

(1) Position the curtain shield airbag assembly inside the tire as shown in the illustration.

Text in Illustration

*a

Width

*b

Inner Diameter

Tire size:

Must exceed the following dimensions

Width:

185 mm (7.28 in.)

Inner diameter:

360 mm (1.18 ft.)

CAUTION:

Make sure that the wire harness is tight. If the wire harness is loose, the curtain shield airbag assembly may become loose due to the shock when the airbag is deployed.

NOTICE:

As the tires may be damaged by the airbag deployment, use a tire that you are planning to throw away.

(e) Install SST.

(1) After connecting SST to each other, connect them to the curtain shield airbag.

SST: 09082-00802

09082-10801

09082-20801

(f) Place the tires.

CAUTION:

CAUTION:

Do not place the deployment direction of the curtain shield airbag facing the ground.

(1) Place at least 2 tires under the tire which the curtain shield airbag assembly is tied to.

Text in Illustration

*a

Tire (2 or more)

(2) Place at least 2 tires over the tire which the curtain shield airbag assembly is tied to. The top tire should have the disc wheel installed.

CAUTION:

  • Do not place SST connector under the tire because it could be damaged.
  • As the disc wheel may be damaged by the airbag deployment, use a disc wheel that you are planning to throw away.
  • As the tires may be damaged by the airbag deployment, use a tire that you are planning to throw away.

(3) Tie the tires together with 2 wire harnesses.

CAUTION:

Make sure that the wire harnesses are tight. Looseness in the wire harnesses results in the tires coming free due to the shock when the airbag is deployed.

(g) Install the SST.

Connect SST connector.

SST: 09082-00700

NOTICE:

To avoid damaging the SST connector and wire harness, do not lock the secondary lock of the twin lock. Also, secure some slack for the SST wire harness inside the tires.

(h) Deploy the airbag.

(1) Connect the red clip of SST to the battery positive (+) terminal and the black clip of SST to the battery negative (-) terminal.

Text in Illustration

*1

Curtain Shield Airbag

*a

Battery

*b

10 m (32.8 ft.) or more

(2) Check that no one is within a 10 m (32.8 ft.) radius of the tire which the curtain shield airbag is tied to.

(3) Press the SST activation switch and deploy the airbag.

CAUTION:

Before deployment, make sure that no one is near the airbag.

HINT:

The airbag is deployed as the LED of the SST activation switch comes on.

(i) Dispose of the curtain shield airbag assembly.

CAUTION:

  • The curtain shield airbag becomes extremely hot when the airbag is deployed, so do not touch it for at least 30 minutes after deployment.
  • Use gloves and safety glasses when handling a curtain shield airbag with a deployed airbag.
  • Do not apply water to a curtain shield airbag with a deployed airbag.
  • Always wash your hands with water after completing the operation.

(1) Remove the curtain shield airbag assembly from the tire.

(2) Dispose of curtain shield airbag assembly, according to local regulations.

On-vehicle Inspection
ON-VEHICLE INSPECTION PROCEDURE 1. INSPECT CURTAIN SHIELD AIRBAG ASSEMBLY (for Vehicle not Involved in Collision) (a) Perform a Diagnostic System Check (See page ). (b) With the curta ...

Installation
INSTALLATION CAUTION / NOTICE / HINT HINT: Use the same procedure for both the RH and LH sides. The procedure described below is for the LH side. PROCEDURE 1. INSTALL CURTAIN SH ...

Other materials:

Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Air Conditioning System DTC Code Detection Item Memory See page B1412 Ambient Temperature Sensor Circuit Memorized (4 seconds or more) B1413 ...

Removal
REMOVAL PROCEDURE 1. REMOVE AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System) (See page ) 2. REMOVE INTEGRATION PANEL SUB-ASSEMBLY (for Manual Cooler System) (See page ) 3. REMOVE TRANSFER POSITION SWITCH (a) Detach the 2 claws to remove the transfer pos ...

Adjustment
ADJUSTMENT PROCEDURE 1. PREPARE VEHICLE FOR FOG LIGHT AIMING ADJUSTMENT (a) Prepare the vehicle: HINT: Ensure that there is no damage or deformation to the body around the fog lights. Fill the fuel tank. Make sure that the oil is filled to the specified level. Make sure ...

В© 2011-2024 Copyright www.ttguide.net