Toyota Tacoma (2015-2018) Service Manual: Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE NO. 1 HEATER TO REGISTER DUCT
|
(a) Remove the 2 screws <F> and screw <D>. |
|
(b) Disengage the 2 guides to remove the No. 1 heater to register duct.
2. REMOVE NO. 3 HEATER TO REGISTER DUCT
|
(a) Remove the 2 screws <F> and screw <D>. |
|
(b) Disengage the 2 guides to remove the No. 3 heater to register duct.
3. REMOVE NO. 2 HEATER TO REGISTER DUCT
|
(a) Remove the 2 screws <F> and screw <D>. |
|
(b) Disengage the 2 guides to remove the No. 2 heater to register duct.
4. REMOVE SIDE NO. 1 DEFROSTER NOZZLE DUCT
|
(a) Remove the 2 screws <F>. |
|
(b) Disengage the 2 guides.
(c) Disengage the 2 claws to remove the side No. 1 defroster nozzle duct.
5. REMOVE SIDE NO. 2 DEFROSTER NOZZLE DUCT
|
(a) Remove the 2 screws <F>. |
|
(b) Disengage the 2 guides.
(c) Disengage the 2 claws to remove the side No. 2 defroster nozzle duct.
6. REMOVE DEFROSTER NOZZLE ASSEMBLY
|
(a) Remove the 3 screws <F>. |
|
(b) Disengage the 3 guides to remove the defroster nozzle assembly.
7. REMOVE NO. 1 INSTRUMENT PANEL REGISTER SUB-ASSEMBLY
|
(a) Disengage the 6 claws and 3 guides to remove the No. 1 instrument panel register sub-assembly. |
|
8. REMOVE NETWORK GATEWAY ECU
.gif)
9. REMOVE NAVIGATION ANTENNA ASSEMBLY (w/ Navigation System)
10. REMOVE ANTENNA CORD SUB-ASSEMBLY
11. REMOVE INSTRUMENT PANEL PASSENGER WITHOUT DOOR AIRBAG ASSEMBLY
12. REMOVE NO. 1 INSTRUMENT PANEL PIN
HINT:
Use the same procedure as for the opposite side.
|
(a) Remove the screw <F>. |
|
(b) Disengage the guide to remove the No. 1 instrument panel pin.
13. REMOVE NO. 1 METER HOOD RETAINER
HINT:
Use the same procedure as for the opposite side.
|
(a) Remove the screw <D>. |
|
(b) Disengage the guide to remove the No. 1 meter hood retainer.
14. REMOVE NO. 1 INSTRUMENT PANEL CUSHION
|
(a) Remove the No. 1 instrument panel cushion. |
|
15. REMOVE NO. 2 INSTRUMENT PANEL CUSHION
|
(a) Remove the No. 2 instrument panel cushion. |
|
16. REMOVE NO. 4 INSTRUMENT PANEL CUSHION
|
(a) Remove the No. 4 instrument panel cushion. |
|
17. REMOVE INSTRUMENT PANEL CUSHION
|
(a) Remove the instrument panel cushion. |
|
Components
COMPONENTS
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
...
Removal
REMOVAL
PROCEDURE
1. TABLE OF BOLT, SCREW AND NUT
HINT:
All bolts, screws and nuts relevant to installing and removing the instrument
panel are shown along with their alphabetic codes in the tab ...
Other materials:
Portable Player cannot be Operated Using In-vehicle Device or Track Information
is not Displayed on In-vehicle Device
PROCEDURE
1.
CHECK USING ANOTHER "Bluetooth" AUDIO COMPATIBLE VEHICLE OF SAME MODEL
(a) Check if track information is displayed normally on another "Bluetooth" audio
compatible vehicle of the same model.
OK:
Track information is displayed no ...
Removal
REMOVAL
PROCEDURE
1. REMOVE WATER INLET WITH THERMOSTAT SUB-ASSEMBLY
(See page )
2. REMOVE NO. 1 RADIATOR HOSE
3. REMOVE NO. 2 RADIATOR HOSE
4. DISCONNECT RADIATOR RESERVE TANK HOSE
5. SEPARATE TRANSMISSION OIL COOLER HOSE (for Automatic Transmission)
(a) Disengage the c ...
On-vehicle Inspection
ON-VEHICLE INSPECTION
PROCEDURE
1. INSPECT SPEEDOMETER
(a) Check speedometer operation.
NOTICE:
The meter ECU receives the vehicle speed signal from the skid control
ECU via CAN communication. Therefore, perform the following inspection referring
to values on the Data List of th ...
