Toyota Tacoma (2015-2018) Service Manual: Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE MILLIMETER WAVE RADAR WIRE (w/ Toyota Safety Sense P)
Click here .gif)
2. REMOVE MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Toyota Safety Sense P)
Click here
3. REMOVE NO. 1 RADIATOR GRILLE GARNISH
(a) When Replacing the No. 1 Radiator Grille Garnish:
(1) Apply protective tape around the spring nut.
.png) |
Protective Tape |
|
(2) Using a plier nipper (side cutters), cut the No. 1 radiator grille garnish at the positions shown in the illustration. |
|
|
(3) Push the No. 1 radiator grille garnish to remove the 2 spring nuts as shown in the illustration. CAUTION: Make sure to cover the spring nuts with a piece of cloth or equivalent to prevent them from flying off during removal. |
|
|
(4) For type A and type B, disengage the 4 claws and 2 pins as shown in the illustration to remove the No. 1 radiator grille garnish. |
|
|
(5) For type C, disengage the 2 claws and the guide as shown in the illustration to remove the No. 1 radiator grille garnish. |
|
(b) When Replacing the Radiator Grille Sub-Assembly:
(1) Using a center punch, make a depression at the positions shown in the illustration.
|
*1 |
Spring Nut |
- |
- |
|
*a |
Depression |
*b |
Pin of No. 1 Radiator Grille Garnish |
|
*c |
Center Line |
- |
- |
HINT:
- Make sure to make the depressions so they are aligned with the center line of the pin of the No. 1 radiator grille garnish.
- Make sure to make the depressions correctly so that a plier nipper (side cutters) can be used to pinch the spring nuts.
(2) Using a plier nipper (side cutters), rotate the 2 spring nuts to align the cutouts of each spring nut as shown in the illustration.
|
*a |
90° |
*b |
Depression |
|
*c |
Cutout |
- |
- |
(3) Using a plier nipper (side cutters), deform each spring nut as shown in the illustration and then remove the 2 spring nuts.
|
*a |
Cutout |
- |
- |
|
(4) For type A and type B, disengage the 4 claws and 2 guides and 2 pins as shown in the illustration to remove the No. 1 radiator grille garnish. |
|
|
(5) For type C, disengage the 2 claws and 3 guides as shown in the illustration to remove the No. 1 radiator grille garnish. |
|
4. REMOVE RADIATOR GRILLE MOULDING
|
(a) Remove the 8 screws. |
|
(b) Disengage the 8 claws to remove the radiator grille moulding.
Removal
REMOVAL
PROCEDURE
1. REMOVE RADIATOR GRILLE
(a) w/ Toyota Safety Sense P
(1) Disconnect the connector.
(2) Disengage the clamp.
(b ...
Installation
INSTALLATION
PROCEDURE
1. INSTALL RADIATOR GRILLE
(a) Engage the 10 guides to install the radiator grille.
(b) Install the 2 clips.
(c) Install the 2 screws.
(d) Remove the protective tape.
(e) ...
Other materials:
Brake Control Signal Mismatch (C1A69)
DESCRIPTION
The skid control ECU (master cylinder solenoid)*1 or skid control ECU (brake
actuator assembly)*2 sends signals to the millimeter wave radar sensor assembly
according to the brake control status. If the millimeter wave radar sensor assembly
receives a vehicle stability control sys ...
Invalid Data Received from Vehicle Dynamics Control Module (U0416)
DESCRIPTION
This DTC is detected if a wheel speed malfunction signal is sent from the skid
control ECU (brake actuator assembly).
DTC No.
Detection Item
DTC Detection Condition
Trouble Area
U0416
Invalid Data Received From V ...
Removal
REMOVAL
CAUTION / NOTICE / HINT
HINT:
Use the same procedure for both the RH and LH sides.
The procedure described below is for the LH side.
PROCEDURE
1. PRECAUTION
CAUTION:
Be sure to read Precaution thoroughly before servicing (See page
).
NOTICE:
After turning the ign ...
