Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Disassembly

DISASSEMBLY

PROCEDURE

1. REMOVE TAIL GATE PROTECTOR

(See page 2. REMOVE TAIL GATE SERVICE HOLE COVER )

2. REMOVE TAIL GATE SERVICE HOLE COVER

(a) Using a T30 "TORX" socket wrench, remove the 8 screws and tail gate service hole cover.

3. REMOVE REAR TELEVISION CAMERA ASSEMBLY

4. REMOVE TAIL GATE LOCK ASSEMBLY LH

4. REMOVE TAIL GATE LOCK ASSEMBLY LH

(a) Disconnect the snap and tail gate lock control link from the tail gate handle assembly as shown in the illustration.

Text in Illustration

*a

Snap

*b

Tail Gate Lock Control Link

(b) Disengage the clamp.

(c) Using a T40 "TORX" socket wrench, remove the 2 bolts and tail gate lock assembly LH.

5. REMOVE TAIL GATE LOCK ASSEMBLY RH

(a) Disconnect the snap and tail gate lock control link from the tail gate handle assembly as shown in the illustration.

Text in Illustration

*a

Snap

*b

Tail Gate Lock Control Link

(b) Disengage the clamp.

(c) Using a T40 "TORX" socket wrench, remove the 2 bolts and tail gate lock assembly RH.

6. REMOVE TAIL GATE LOCK CONTROL LINK

(a) Disconnect the snap to remove the tail gate lock control link from the tail gate lock assembly LH as shown in the illustration.

Text in Illustration

*a

Snap

HINT:

Use the same procedure for the LH side and RH side.

7. REMOVE TAIL GATE HANDLE ASSEMBLY

(a) Remove the 2 bolts.

(b) Disengage the guide to remove the tail gate handle assembly.

8. REMOVE TAIL GATE LOCK STRIKER

(a) Using a T40 "TORX" socket wrench, remove the 2 bolts and tail gate lock striker.

HINT:

Use the same procedure for the LH side and RH side.

9. REMOVE TAIL GATE

(a) Disengage the clamp.

(b) Disengage the clamp.

(c) Disengage the 2 claws and 2 guides to disconnect the wire harness from the tail gate.

Text in Illustration

*a

Guide

*b

Clamp

(d) Disengage the tail gate stay from the tail gate stay stopper as shown in the illustration.

HINT:

Use the same procedure for the LH side and RH side.

(e) Remove the tail gate from the vehicle in the order shown in the illustration.

NOTICE:

Be careful not to drop the tail gate.

HINT:

Remove the tail gate from the vehicle by lifting up the right side and sliding it slightly to the right.

10. REMOVE TAIL GATE STAY STOPPER

(a) Using a T40 "TORX" socket wrench, remove the tail gate stay shaft and tail gate stopper.

HINT:

Use the same procedure for the LH side and RH side.

11. REMOVE TAIL GATE STAY ASSEMBLY

(a) Using a T40 "TORX" socket wrench, remove the tail gate stay shaft, washer and tail gate stay assembly.

HINT:

Use the same procedure for the LH side and RH side.

12. REMOVE TAIL GATE HINGE ASSEMBLY LH

(a) Using a T40 "TORX" socket wrench, remove the bolt, 2 screws and tail gate hinge assembly LH.

13. REMOVE TAIL GATE HINGE ASSEMBLY RH

(a) Using a T40 "TORX" socket wrench, remove the bolt, 2 screws and tail gate hinge assembly RH.

14. REMOVE SIDE GATE SUPPORT FEMALE HINGE RH

(a) Disengage the claw to remove the side gate support female hinge RH.

15. REMOVE NO. 2 REAR BODY NAME PLATE (for 4WD)

16. REMOVE NO. 3 REAR BODY NAME PLATE (for 2GR-FKS) 16. REMOVE NO. 3 REAR BODY NAME PLATE (for 2GR-FKS)

16. REMOVE NO. 3 REAR BODY NAME PLATE (for 2GR-FKS)

Reassembly Reassembly

Components
COMPONENTS ILLUSTRATION ILLUSTRATION ILLUSTRATION ...

Reassembly
REASSEMBLY PROCEDURE 1. INSTALL NO. 3 REAR BODY NAME PLATE (for 2GR-FKS) 2. INSTALL NO. 2 REAR BODY NAME PLATE (for 4WD) 3. INSTALL SIDE GATE SUPPORT FEMALE HINGE RH (a) Engage ...

Other materials:

Dtc Check / Clear
DTC CHECK / CLEAR 1. CHECK FOR DTC HINT: When using the Techstream with the engine switch off, connect the Techstream to the DLC3 and turn a courtesy light switch on and off at intervals of 1.5 seconds or less until communication between the Techstream and the vehicle begins. Then select th ...

Removal
REMOVAL PROCEDURE 1. REMOVE FRONT WHEEL 2. REMOVE REAR WHEEL 3. REMOVE TIRE PRESSURE WARNING VALVE AND TRANSMITTER (a) Remove the cap and valve core to release the air from the tire. NOTICE: Keep the removed cap and valve core. (b) After ensuring that a sufficient amount of air has been rele ...

Front Camera Module Circuit (C1AA0)
DESCRIPTION When an internal malfunction is detected in the forward recognition camera, DTC C1AA0 is stored. DTC No. Detection Item DTC Detection Condition Trouble Area C1AA0 Front Camera Module Circuit 3 seconds ...

В© 2011-2024 Copyright www.ttguide.net