Toyota Tacoma manuals

Toyota Tacoma (2015-2018) Service Manual: Differential Oil

Adjustment

ADJUSTMENT

PROCEDURE

1. INSPECT DIFFERENTIAL OIL

(a) Stop the vehicle on a level place.

(a) Stop the vehicle on a level place.

(b) Remove the differential filler plug and gasket.

(c) Check that the oil level is within 5 mm (0 to 0.20 in.) of the bottom of the filler plug opening.

NOTICE:

  • Excessively large or small quantities of oil may cause problems.
  • After replacing the oil, drive the vehicle and check the oil level again.

HINT:

If necessary, fill the differential carrier assembly with differential gear oil.

Oil type and viscosity:

Toyota Genuine Differential gear oil LT SAE 75W-85 APL GL-5 or equivalent.

Capacity:

Front differential carrier assembly:

1.45 to 1.55 liters

(1.54 to 1.64 US qts, 1.28 to 1.36 Imp. qts)

Rear differential carrier assembly (for BD20D (EX Long Wheelbase )):

2.85 to 2.95 liters

(3.01 to 3.12 US qts, 2.51 to 2.60 Imp. qts)

Rear differential carrier assembly (for BD20D (SP Long Wheelbase)):

3.00 to 3.10 liters

(3.17 to 3.28 US qts, 2.64 to 2.73 Imp. qts)

Rear differential carrier assembly (for BD22A (EX Long Wheelbase)):

3.75 to 3.85 liters

(3.96 to 4.07 US qts, 3.30 to 3.39 Imp. qts)

Rear differential carrier assembly (for BD22AN (EX Long Wheelbase)):

3.75 to 3.85 liters

(3.96 to 4.07 US qts, 3.30 to 3.39 Imp. qts)

Rear differential carrier assembly (for BD22AN (SP Long Wheelbase)):

3.95 to 4.05 liters

(4.17 to 4.28 US qts, 3.48 to 3.56 Imp. qts)

(d) Check for oil leakage if the oil level is low.

(e) Install the differential filler plug and a new gasket.

Torque:

Front differential carrier assembly :

39 N·m {398 kgf·cm, 29 ft·lbf}

Rear differential carrier assembly :

49 N·m {500 kgf·cm, 36 ft·lbf}

Installation
INSTALLATION PROCEDURE 1. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER (a) Install a new front differential drive pinion bearing spacer. HINT: Make sure the front differential drive pini ...

Differential Side Gear Shaft Oil Seal(for 4wd)
...

Other materials:

Brake
General Maintenance GENERAL MAINTENANCE PROCEDURE 1. INSPECT BRAKE LINE PIPES AND HOSES HINT: Work in a well-lighted area. Turn the front wheels fully to the right or left before beginning. (a) Check all the brake lines and hoses for: Damage Wear Deformation Cracks ...

Removal
REMOVAL PROCEDURE 1. PRECAUTION CAUTION: Be sure to read Precaution thoroughly before servicing (See page ). NOTICE: After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the ...

Display does not Dim when Light Control Switch is Turned ON
PROCEDURE 1. CHECK IMAGE QUALITY SETTING (a) Display the "Display" screen. (b) Turn the light control switch to the tail or head position. (c) Check if "Day Mode" on the display adjustment screen is on. OK: "Day Mode" setting is of ...

© 2011-2024 Copyright www.ttguide.net