Toyota Tacoma (2015-2018) Service Manual: Data List / Active Test
DATA LIST / ACTIVE TEST
1. READ DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / (desired system) / Data List / All Data.
(e) Read the Data List according to the display on the Techstream.
Master Switch|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
D Door P/W Auto SW |
Driver side power window auto switch signal / ON or OFF |
ON: Driver side power window auto switch operated OFF: Driver side power window auto switch not operated |
- |
|
P Door P/W Auto SW |
Front passenger side power window auto up/down switch signal / ON or OFF |
ON: Front passenger side power window auto switch operated OFF: Front passenger side power window auto switch not operated |
- |
|
P Door P/W Up SW |
Front passenger side power window manual up switch signal / ON or OFF |
ON: Front passenger side power window manual up switch operated OFF: Front passenger side power window manual up switch not operated |
- |
|
P Door P/W Down SW |
Front passenger side power window manual down switch signal / ON or OFF |
ON: Front passenger side power window manual down switch operated OFF: Front passenger side power window manual down switch not operated |
- |
|
Door Lock Switch Status |
Driver side door control switch lock signal / ON or OFF |
ON: Door control switch pushed to lock position OFF: Door control switch not pushed to lock position |
- |
|
Door Unlock Switch Status |
Driver side door control switch unlock signal / ON or OFF |
ON: Door control switch pushed to unlock position OFF: Door control switch not pushed to unlock position |
- |
|
Window Lock Switch Status |
Window lock switch signal / ON or OFF |
ON: Window lock switch LOCK position OFF: Window lock switch UNLOCK position |
- |
|
Number of Trouble Codes |
Number of trouble codes / Min.: 0 or Max.: 255 |
Number of DTCs will be displayed |
- |
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
D Door P/W Auto SW |
Driver side power window auto switch signal / ON or OFF |
ON: Driver side power window auto switch operated OFF: Driver side power window auto switch not operated |
- |
|
D Door P/W Up SW |
Driver side power window manual up switch signal / ON or OFF |
ON: Driver side power window manual up switch operated OFF: Driver side power window manual up switch not operated |
- |
|
D Door P/W Down SW |
Driver side power window manual down switch signal / ON or OFF |
ON: Driver side power window manual down switch operated OFF: Driver side power window manual down switch not operated |
- |
|
Glass Position (Close - 1/4) |
Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution |
OK: Normal manual up operation Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
|
Glass Position (1/4 - 2/4) |
Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution |
OK: Normal manual up operation Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
|
Glass Position (2/4 - 3/4) |
Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution |
OK: Normal manual up operation Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
|
Glass Position (3/4 - Open) |
Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution |
OK: Normal manual up operation Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
|
D Window Auto Up |
Auto up operation using the multiplex network master switch assembly / ON or OFF |
Customization status displayed |
- |
|
D Window Auto Down |
Auto down operation using the multiplex network master switch assembly / ON or OFF |
Customization status displayed |
- |
|
Number of Trouble Codes |
Number of trouble codes / Min.: 0 or Max.: 255 |
Number of DTCs will be displayed |
- |
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
P Door P/W Auto SW |
Front passenger side power window auto switch signal / ON or OFF |
ON: Front passenger side power window auto switch operated OFF: Front passenger side power window auto switch not operated |
- |
|
P Door P/W Up SW |
Front passenger side power window manual up switch signal / ON or OFF |
ON: Front passenger side power window manual up switch operated OFF: Front passenger side power window manual up switch not operated |
- |
|
P Door P/W Down SW |
Front passenger side power window manual down switch signal / ON or OFF |
ON: Front passenger side power window manual down switch operated OFF: Front passenger side power window manual down switch not operated |
- |
|
Glass Position (Close - 1/4) |
Margin for jam protection triggering force of window glass within range of fully closed to 1/4 open window glass position / OK or Caution |
OK: Normal manual up operation Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
|
Glass Position (1/4 - 2/4) |
Margin for jam protection triggering force of window glass within range of 1/4 to 1/2 open window glass position / OK or Caution |
OK: Normal manual up operation Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
|
Glass Position (2/4 - 3/4) |
Margin for jam protection triggering force of window glass within range of 1/2 to 3/4 open window glass position / OK or Caution |
OK: Normal manual up operation Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
|
Glass Position (3/4 - Open) |
Margin for jam protection triggering force of window glass within range of 3/4 to fully open window glass position / OK or Caution |
OK: Normal manual up operation Caution: Jam detected in the specified range |
Caution is displayed only while the power window ECU built into the power window regulator motor assembly detects a jam. |
|
P Window Auto Up |
Auto up operation using the front power window regulator switch assembly RH / ON or OFF |
Customization status displayed |
- |
|
P Window Auto Up From Driver |
Remote auto up operation using the multiplex network master switch assembly / ON or OFF |
Customization status displayed |
- |
|
P Window Auto Down |
Auto down operation using the front power window regulator switch assembly RH / ON or OFF |
Customization status displayed |
- |
|
P Window Auto Down From Driver |
Remote auto down operation using the multiplex network master switch assembly / ON or OFF |
Customization status displayed |
- |
|
Number of Trouble Codes |
Number of trouble codes / Min.: 0 or Max.: 255 |
Number of DTCs will be displayed |
- |
|
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|
|
FR Door Courtesy |
Front door courtesy light switch RH signal / ON or OFF |
ON: Front passenger side door closed OFF: Front passenger side door open |
- |
|
FL Door Courtesy |
Front door courtesy light switch LH signal / ON or OFF |
ON: Driver side door closed OFF: Driver side door open |
- |
|
Communication P-Door Motor |
Connection status between front power window regulator motor assembly RH and main body ECU / OK or STOP |
OK: Normal communication STOP: Communication stopped |
- |
|
Communication Master SW |
Connection status between multiplex network master switch and main body ECU / OK or STOP |
OK: Normal communication STOP: Communication stopped |
- |
2. ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / (desired system) / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
CAUTION:
Be careful to avoid injuries as this test causes vehicle parts to move. During the Active Test, the jam protection function will not operate.
D-Door Motor (Front Power Window Regulator Motor Assembly LH)|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Power Window |
Power window |
OFF / UP /DOWN |
- |
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Power Window |
Power window |
OFF / UP /DOWN |
- |
|
Tester Display |
Test Part |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
IG OFF P/W Control Permission Output |
Power window |
OFF / ON |
Perform this Active Test with the ignition switch off |
Terminals Of Ecu
TERMINALS OF ECU
1. CHECK POWER WINDOW REGULATOR MASTER SWITCH ASSEMBLY
(a) for Double Cab
(1) Disconnect the P18 power window regulator master switch assembly connector.
(2) Measure the voltage ...
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
Power Window Control System
DTC Code
Detection Item
See page
B2311
Power Window Motor Malfunction
...
Other materials:
Diagnosis System
DIAGNOSIS SYSTEM
DIAGNOSIS FUNCTION
(a) The diagnosis function turns off the cruise control indicator, illuminates
the master warning light and displays a warning message when a malfunction is detected.
When a malfunction is detected in the dynamic radar cruise control system, DTCs
are store ...
Speed Signal Circuit
DESCRIPTION
The combination meter assembly receives the vehicle speed signal from this circuit.
The wheel speed sensors produce an output that varies according to the vehicle speed.
The wheel speed sensor output is received by the skid control ECU, which uses this
information to create the ve ...
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
LANE DEPARTURE ALERT SYSTEM
DTC No.
Detection Item
Link
C1A47
Steering Angle Sensor
C1AA0
Front Camera Module Circuit
C1AA1
F ...
