Toyota Tacoma (2015-2018) Service Manual: Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
HINT:
Using the Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / LKA/LDA / Data List.
(e) According to the display on the Techstream, read the Data List.
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
Load System |
Type of system vehicle is equipped with/ LDA or LKA |
LDA or LKA |
LDA: Equipped with lane departure alert system |
LKA: Equipped with lane keeping assist system |
|
LDA Control |
Control status of lane departure alert system |
Prohibit or Permit |
Prohibit: Control prohibited Permit: Control permitted |
- |
|
Turn Signal Switch (Right) |
Turn signal switch (right) status |
OFF or ON |
ON: Turn signal light switch on (right) OFF: Turn signal light switch off |
- |
|
Turn Signal Switch (Left) |
Turn signal switch (left) status |
OFF or ON |
ON: Turn signal light switch on (left) OFF: Turn signal light switch off |
- |
|
Skid Control Buzzer Demand |
Lane departure alert buzzer demand status |
OFF or ON |
ON: Lane departure alert buzzer operating OFF: Lane departure alert buzzer not operating |
- |
|
Vehicle Information (2WD/4WD) |
Vehicle information (drivetrain) stored in forward recognition camera |
2WD, 4WD or Unknown |
2WD: for 2WD 4WD: for 4WD |
Unknown: Vehicle information not confirmed |
|
Vehicle Information (Conv/HV) |
Vehicle information (conventional/hybrid) stored in forward recognition camera |
Conv, HV or Unknown |
Conv: Conventional |
HV: Hybrid vehicle Unknown: Vehicle information not confirmed |
|
The Number of DTCs |
Number of stored DTCs |
min.: 0, max.: 255 |
Number of stored DTCs |
- |
ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Chassis / LKA/LDA / Active Test.
(e) According to the display on the Techstream, perform the Active Test.
HINT:
The ignition switch must be turned to ON to proceed with the Active Test using the Techstream.
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
LDA Buzzer |
Sounds the lane departure alert buzzer |
OFF or ON |
Confirm that the vehicle is stopped with the ignition switch ON. |
(f) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(g) According to the display on the Techstream, perform the Active Test.
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Meter Display 1 |
Multi-information display |
ALL or OFF |
Perform the test with the vehicle stopped and engine idling |
Freeze Frame Data
FREEZE FRAME DATA
DESCRIPTION
(a) Whenever a lane departure alert system is stored, the forward recognition
camera stores the current vehicle state (ECU and sensor information) as Freeze Frame
D ...
Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART
LANE DEPARTURE ALERT SYSTEM
DTC No.
Detection Item
Link
C1A47
Steering Angle Sensor
...
Other materials:
Diagnosis System
DIAGNOSIS SYSTEM
DIAGNOSIS FUNCTION
(a) The diagnosis function turns off the cruise control indicator, illuminates
the master warning light and displays a warning message when a malfunction is detected.
When a malfunction is detected in the dynamic radar cruise control system, DTCs
are store ...
System Description
SYSTEM DESCRIPTION
1. FRONT SEAT HEATER
(a) By operating the seat heater switch on the air conditioning control assembly,
the temperature can be controlled within the range of 36 to 42.2°C (96 to 108°F).
(b) The on/off status and heater level of each seat heater are indicated by the
respect ...
Steering Pad Switch
Components
COMPONENTS
ILLUSTRATION
Removal
REMOVAL
PROCEDURE
1. REMOVE STEERING PAD
(See page
)
2. REMOVE STEERING PAD SWITCH ASSEMBLY
(a) Disconnect the 2 connectors.
(b) Disengage the 2 clamps.
(c) Remove the 4 screws.
...
