Toyota Tacoma (2015-2018) Service Manual: Cruise SET Indicator Light Circuit
DESCRIPTION
The ECM illuminates the cruise control SET indicator by sending indicator output demand signals to the combination meter assembly via CAN communication. The cruise control SET indicator illuminates when the dynamic radar cruise control system is controlling vehicle speed. The cruise SET indicator light circuit uses CAN communication. If the cruise control SET indicator is not functioning correctly, check for CAN communication DTCs before troubleshooting this circuit.
CAUTION / NOTICE / HINT
CAUTION:
Observe the following items for safety reasons when using Techstream:
- Before using the Techstream, read the instruction Techstream.
- Prevent the Techstream cable from being caught on the pedals, shift lever or steering wheel when driving with the Techstream connected to the vehicle.
- When driving the vehicle for testing purposes, 2 people are required. One person should operate the Techstream while the other drives the vehicle.
NOTICE:
- Before replacing the ECM, refer to Registration.
w/o Smart Key System: Click here
.gif)
w/ Smart Key System: Click here
- When replacing the combination meter assembly, always replace it with a new one. If a combination meter assembly which was installed to another vehicle is used, the information stored in it will not match the information from the vehicle and a DTC may be stored.
PROCEDURE
|
1. |
PERFORM ACTIVE TEST USING TECHSTREAM (METER DISPLAY 1) |
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn the Techstream on.
(d) Enter the following menus: Body Electrical / Combination Meter / Active Test.
(e) Perform the Active Test according to the display on the Techstream.
Body Electrical > Combination Meter > Active Test
|
Tester Display |
Measurement Item |
Control Range |
Diagnostic Note |
|---|---|---|---|
|
Meter Display 1 |
Multi-information display |
OFF, 6 to 0 or All |
- |
|
Result |
Proceed to |
|---|---|
|
The multi-information display in the combination meter assembly turns on or off according to the operation of the Active Test. |
A |
|
The multi-information display in the combination meter assembly does not turn on or off according to the operation of the Active Test. |
B |
| B | .gif) |
GO TO METER / GAUGE SYSTEM |
|
.gif)
|
2. |
READ VALUE USING TECHSTREAM (-SET SWITCH) |
(a) Turn the cruise control system on using the cruise control main switch (ON-OFF button).
(b) Drive at a speed between approximately 40 km/h (25 mph) and 180 km/h (110 mph).
(c) Enter the following menus: Powertrain / Radar Cruise1 / Data List.
(d) Read the Data List according to the display on the Techstream.
Powertrain > Radar Cruise1 > Data List
|
Tester Display |
Measurement Item |
Range |
Normal Condition |
Diagnostic Note |
|---|---|---|---|---|
|
-SET Switch |
-SET switch status |
ON or OFF |
ON: -SET switch on OFF: -SET switch off |
- |
|
Result |
Proceed to |
|---|---|
|
The cruise control SET indicator illuminates and turns off according to the operation of the cruise control main switch (-SET switch). |
A |
|
The cruise control SET indicator does not illuminate but the Data List item -SET Switch changes according to the operation of the cruise control main switch (-SET switch). |
B |
|
The cruise control SET indicator does not illuminate and the Data List item -SET Switch does not change according to the operation of the cruise control main switch (-SET switch). |
C |
| A | |
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE |
| B | |
REPLACE COMBINATION METER ASSEMBLY |
| C | |
REPLACE ECM |
Distance Control Switch Circuit
DESCRIPTION
The distance control switch is used to set the distance for vehicle-to-vehicle
distance control mode. The distance control switch is installed in the steering
pad switch assembly. The ...
Neutral Position Switch Circuit
DESCRIPTION
The ECM uses the neutral position switch installed to the manual transmission
assembly to detect when the transmission is in the neutral position.
WIRING DIAGRAM
PROCEDURE
...
Other materials:
Diagnosis System
DIAGNOSIS SYSTEM
1. DESCRIPTION
(a) Smart key system (for start function) data and the Diagnostic Trouble Codes
(DTCs) can be read through the Data Link Connector 3 (DLC3) of the vehicle. When
the system seems to be malfunctioning, use the Techstream to check for malfunctions
and perform rep ...
Inspection
INSPECTION
PROCEDURE
1. INSPECT PARK/NEUTRAL POSITION SWITCH
(a) Measure the resistance according to the value(s) in the table below.
Text in Illustration
*a
Component without harness connected
(Park/Neutral Position Switch)
...
Vehicle Speed Tolerance Malfunction (C1AA2)
DESCRIPTION
The forward recognition camera receives vehicle speed tolerance signals from
the combination meter assembly. If the combination meter assembly detects a vehicle
speed tolerance malfunction signal, it informs the forward recognition camera via
CAN communication, and DTC C1AA2 is st ...
