DESCRIPTION
When CRAWL starts after operating the CRAWL switch (drive monitor switch), the CRAWL indicator light turns on. While CRAWL is in the process of stopping, the CRAWL indicator light begins blinking. When CRAWL totally stops, the CRAWL indicator light turns off.
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
PROCEDURE
1. |
CHECK CAN COMMUNICATION SYSTEM |
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (See page ).
OK:
CAN Bus Check indicates no malfunctions in CAN communication.
NG |
GO TO CAN COMMUNICATION SYSTEM (HOW TO PROCEED WITH TROUBLESHOOTING) |
|
2. |
INSPECT SKID CONTROL ECU (TRS TERMINAL) |
(a) Disconnect the S1 skid control ECU (master cylinder solenoid) connector.
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
(c) Reconnect the S1 skid control ECU (master cylinder solenoid) connector.
NG |
GO TO STEP 4 |
|
3. |
READ VALUE USING TECHSTREAM (CRAWL CONTROL LIGHT) |
(a) Turn the ignition switch off.
(b) Connect the Techstream to the DLC3.
(c) Turn the ignition switch to ON.
(d) Turn the Techstream on.
(e) Enter the following menus: Chassis / ABS/VSC/TRAC / Active Test.
(f) According to the display on the Techstream, read the Data List.
ABS/VSC/TRAC
Tester Display |
Measurement Item/Range |
Normal Condition |
Diagnostic Note |
---|---|---|---|
Crawl Control Light |
Crawl indicator light/ ON or OFF |
ON: Indicator light on OFF: Indicator light off |
- |
(g) Check the Techstream display condition of the brake warning light.
Result
Result |
Proceed to |
---|---|
Display of the Data List remains OFF |
A |
Display of the Data List remains ON |
B |
A |
GO TO METER / GAUGE SYSTEM |
B |
REPLACE MASTER CYLINDER SOLENOID |
4. |
INSPECT DRIVE MONITOR SWITCH |
(a) Remove the crawl control switch (drive monitor switch) (See page ).
(b) Inspect the crawl control switch (drive monitor switch) (See page ).
NG |
REPLACE DRIVE MONITOR SWITCH |
|
5. |
INSPECT ROOF CONSOLE BOX ASSEMBLY |
(a) Remove the roof console box assembly.
*a |
Component without harness connected (Roof Console Box Assembly) |
- |
- |
(b) Measure the resistance according the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
R44-1 (SWI3) - 2 |
Always |
Below 1 Ω |
R44-3 (DN) - 7 |
Always |
Below 1 Ω |
R44-4 (ECU) - 6 |
Always |
Below 1 Ω |
R44-5 (UP) - 3 |
Always |
Below 1 Ω |
R44-12 (GND) - 5 |
Always |
Below 1 Ω |
Result |
Proceed to |
---|---|
OK |
A |
NG (for Double Cab) |
B |
NG (for Access Cab) |
C |
A |
REPAIR OR REPLACE HARNESS OR CONNECTOR (MASTER CYLINDER SOLENOID - ROOF CONSOLE BOX ASSEMBLY) |
B |
REPLACE ROOF CONSOLE BOX ASSEMBLY |
C |
REPLACE ROOF CONSOLE BOX ASSEMBLY |
System Diagram
SYSTEM DIAGRAM
Communication Table
Sender
Receiver
Signal
Line
Millimeter Wave Radar Sensor Assembly
Forward Recognition Camera
Pre-collision alarm signal
Pre-collision braking operation signal
...
Removal
REMOVAL
PROCEDURE
1. PRECAUTION
NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting
the cable from the negative (-) battery terminal. Therefore, make sure to read the
disconnecting the cable from the negative (-) battery terminal notices before pr ...
Reassembly
REASSEMBLY
PROCEDURE
1. INSTALL OIL PUMP COVER
(a) Apply fresh engine oil to the drive and driven rotors.
(b) Place the drive and driven rotors into the timing chain cover assembly
with the marks facing the oil pump cover side.
Text in Illustration
*a
...