COMPONENTS
ILLUSTRATION
ILLUSTRATION
ILLUSTRATION
*1 |
CAMSHAFT |
*2 |
CAMSHAFT BEARING CAP |
*3 |
CAMSHAFT HOUSING SUB-ASSEMBLY RH |
*4 |
CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 1) |
*5 |
CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 1) |
*6 |
CAMSHAFT TIMING GEAR ASSEMBLY |
*7 |
CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY RH |
*8 |
FUEL PUMP LIFTER HOUSING |
*9 |
NO. 1 STRAIGHT PIN |
*10 |
NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
*11 |
NO. 2 CAMSHAFT |
*12 |
NO. 2 CHAIN SUB-ASSEMBLY |
*13 |
NO. 2 CHAIN TENSIONER ASSEMBLY |
*14 |
OIL CONTROL VALVE FILTER RH |
*15 |
RING PIN |
*16 |
VALVE LASH ADJUSTER ASSEMBLY |
*17 |
VALVE STEM CAP |
*18 |
GASKET |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
*T1 |
Type A: 120 N*m (1224 kgf*cm, 89 ft.*lbf) Type B: 95 N*m (969 kgf*cm, 70 ft.*lbf) |
- |
- |
ILLUSTRATION
*1 |
CAMSHAFT BEARING CAP |
*2 |
CAMSHAFT HOUSING SUB-ASSEMBLY LH |
*3 |
CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY LH |
*4 |
CAMSHAFT TIMING GEAR ASSEMBLY |
*5 |
CAMSHAFT TIMING GEAR BOLT (for Exhaust Side of Bank 2) |
*6 |
CAMSHAFT TIMING GEAR BOLT (for Intake Side of Bank 2) |
*7 |
NO. 1 STRAIGHT PIN |
*8 |
NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY |
*9 |
NO. 2 CHAIN SUB-ASSEMBLY |
*10 |
NO. 3 CAMSHAFT SUB-ASSEMBLY |
*11 |
NO. 3 CHAIN TENSIONER ASSEMBLY |
*12 |
NO. 4 CAMSHAFT SUB-ASSEMBLY |
*13 |
OIL CONTROL VALVE FILTER LH |
*14 |
RING PIN |
*15 |
VALVE LASH ADJUSTER ASSEMBLY |
*16 |
VALVE STEM CAP |
*17 |
GASKET |
- |
- |
N*m (kgf*cm, ft.*lbf): Specified torque |
● |
Non-reusable part |
|
*T1 |
Type A: 120 N*m (1224 kgf*cm, 89 ft.*lbf) Type B: 95 N*m (969 kgf*cm, 70 ft.*lbf) |
- |
- |
ILLUSTRATION
ILLUSTRATION
Rear Left Sensor Malfunction (C1AE6)
DESCRIPTION
The No. 1 ultrasonic sensor (rear corner sensor LH) is installed on the rear
bumper. The ECU detects obstacles based on signals received from the No. 1 ultrasonic
sensor (rear corner sensor LH). If the No. 1 ultrasonic sensor (rear corner sensor
LH) has an open circuit or other ma ...
Hazard Warning Switch Circuit
DESCRIPTION
The combination meter assembly receives information signals from the telltale
light assembly (hazard warning signal switch).
WIRING DIAGRAM
CAUTION / NOTICE / HINT
NOTICE:
Inspect the fuses for circuits related to this system before performing the following
inspection procedur ...
Output Speed Sensor Circuit Short to Battery (P072012,P072014,P072031)
DESCRIPTION
This sensor detects the rotation speed of the transmission output shaft and sends
signals to the ECM. By comparing the input turbine speed signal (NT) with the output
shaft speed sensor signal (SP2), the ECM detects the shift timing of the gears and
appropriately controls the engi ...