Toyota Tacoma (2015-2018) Service Manual: Components
COMPONENTS
ILLUSTRATION
|
*A |
w/o Woofer |
*B |
w/ Woofer |
|
*1 |
LUGGAGE COMPARTMENT SIDE TRAY LH |
*2 |
LUGGAGE COMPARTMENT SIDE TRAY RH |
ILLUSTRATION
|
*1 |
COWL SIDE TRIM BOARD LH |
*2 |
FRONT DOOR OPENING TRIM WEATHERSTRIP LH |
|
*3 |
FRONT DOOR SCUFF PLATE LH |
*4 |
FRONT PILLAR GARNISH LH |
|
*5 |
REAR DOOR OPENING TRIM WEATHERSTRIP LH |
*6 |
REAR DOOR SCUFF PLATE LH |
ILLUSTRATION
|
*1 |
ASSIST GRIP SUB-ASSEMBLY |
*2 |
COWL SIDE TRIM BOARD RH |
|
*3 |
FRONT DOOR OPENING TRIM WEATHERSTRIP RH |
*4 |
FRONT DOOR SCUFF PLATE RH |
|
*5 |
FRONT PILLAR GARNISH RH |
*6 |
REAR DOOR OPENING TRIM WEATHERSTRIP RH |
|
*7 |
REAR DOOR SCUFF PLATE RH |
- |
- |
ILLUSTRATION
|
*1 |
CENTER PILLAR LOWER GARNISH LH |
*2 |
CENTER PILLAR UPPER GARNISH LH |
|
*3 |
FRONT SEAT OUTER BELT ASSEMBLY LH |
*4 |
LAP BELT OUTER ANCHOR COVER |
|
*5 |
QUARTER TRIM INSIDE BOARD LH |
*6 |
QUARTER TRIM LOWER PANEL LH |
|
*7 |
REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY LH |
- |
- |
.png) |
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
|
*1 |
CENTER PILLAR LOWER GARNISH RH |
*2 |
CENTER PILLAR UPPER GARNISH RH |
|
*3 |
FRONT SEAT OUTER BELT ASSEMBLY RH |
*4 |
LAP BELT OUTER ANCHOR COVER |
|
*5 |
QUARTER TRIM INSIDE BOARD RH |
*6 |
QUARTER TRIM LOWER PANEL RH |
|
*7 |
REAR SEAT 3 POINT TYPE OUTER BELT ASSEMBLY RH |
- |
- |
|
|
N*m (kgf*cm, ft.*lbf): Specified torque |
- |
- |
ILLUSTRATION
.png)
|
*A |
w/ Vanity Light |
*B |
w/o Vanity Light |
|
*C |
w/ EC Mirror |
- |
- |
|
*1 |
INNER REAR VIEW MIRROR COVER |
*2 |
ROOF CONSOLE BOX ASSEMBLY |
|
*3 |
VISOR ASSEMBLY LH |
*4 |
VISOR ASSEMBLY RH |
|
*5 |
VISOR HOLDER LH |
*6 |
VISOR HOLDER RH |
ILLUSTRATION
|
*A |
w/ Toyota Safety Sense P |
- |
- |
|
*1 |
ASSIST GRIP SUB-ASSEMBLY |
*2 |
COAT HOOK |
|
*3 |
NO. 1 FORWARD RECOGNITION COVER |
*4 |
NO. 1 ROOM LIGHT ASSEMBLY |
|
*5 |
COVER |
*6 |
ASSIST GRIP COVER |
ILLUSTRATION
|
*A |
w/o Sliding Roof |
*B |
w/ Sliding Roof |
|
*1 |
ROOF HEADLINING ASSEMBLY |
- |
- |
ILLUSTRATION
|
*A |
w/o Sliding Roof |
*B |
w/ Vanity Light |
|
*C |
w/o Vanity Light |
*D |
w/ EC Mirror |
|
*E |
w/o EC Mirror |
*F |
w/o Toyota Safety Sense P |
|
*1 |
MICROPHONE CASE |
*2 |
NO. 1 ROOF WIRE |
|
*3 |
NO. 2 ANTENNA CORD SUB-ASSEMBLY |
*4 |
TELEPHONE MICROPHONE ASSEMBLY |
ILLUSTRATION
|
*A |
w/ Sliding Roof |
*B |
w/ Vanity Light |
|
*C |
w/o Vanity Light |
*D |
w/ EC Mirror |
|
*E |
w/o EC Mirror |
*F |
w/o Toyota Safety Sense P |
|
*1 |
MICROPHONE CASE |
*2 |
NO. 1 ROOF WIRE |
|
*3 |
NO. 2 ANTENNA CORD SUB-ASSEMBLY |
*4 |
TELEPHONE MICROPHONE ASSEMBLY |
Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE TELEPHONE MICROPHONE ASSEMBLY
Click here
2. REMOVE MICROPHONE CASE
(a) w/o Sliding Roof:
(1) Disengage the claw and guide to remove the microphone ...
Other materials:
Removal
REMOVAL
PROCEDURE
1. REMOVE REFRIGERANT FROM REFRIGERATION SYSTEM
2. REMOVE AIR CONDITIONER PRESSURE SENSOR
(a) Disconnect the connector.
(b) Using a 27 mm deep socket wrench, remove the air conditioner pressure
sensor.
T ...
Confirm Cellular Phone Functionality
PROCEDURE
1.
CHECK CUSTOMER'S CELLULAR PHONE COMPATIBILITY
(a) Check if the cellular phone is compatible (Refer to http://www.toyota.com/entune/).
Result
Result
Proceed to
Cellular phone is compatible
A
...
Registration
REGISTRATION
PROCEDURE
1. BEFORE REGISTRATION
NOTICE:
The transmitter ID is written on the tire pressure warning valve and transmitter.
It is not possible to read the transmitter ID after installing the tire onto the
wheel. Therefore, make a note of the transmitter ID before installing the t ...
