DESCRIPTION
There may be a short circuit between the CAN main bus lines and/or CAN branch lines when the resistance between terminals 6 (CA3H) and 21 (CA3L) of the central gateway ECU (network gateway ECU) is below 54 Ω.
Detection Item |
Trouble Area |
---|---|
Resistance between terminals 6 (CA3H) and 21 (CA3L) of central gateway ECU (network gateway ECU) is below 54 Ω. |
|
WIRING DIAGRAM
CAUTION / NOTICE / HINT
CAUTION:
When performing the confirmation driving pattern, obey all speed limits and traffic laws.
NOTICE:
Click here
Click here
Click here
DTC check procedure: Turn the ignition switch to ON and wait for 1 minute or more. Then operate the suspected malfunctioning system and drive the vehicle at 60 km/h (37 mph) or more for 5 minutes or more.
Click here
HINT:
PROCEDURE
1. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR) |
(a) Disconnect the cable from the negative (-) battery terminal.
(b) Disconnect the No. 6 CAN junction connector.
(c) Measure the resistance according to the value(s) in the table below.
Text in Illustration
*a |
Front view of wire harness connector (to No. 6 CAN junction connector) |
*b |
to Central Gateway ECU (Network Gateway ECU) |
*c |
to Navigation Receiver Assembly (for Navigation Receiver Type) or Radio and Display Receiver Assembly (for Radio and Display Type) |
- |
- |
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
Connected to |
---|---|---|---|
J22-9 (CANH) - J22-20 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
Central gateway ECU (network gateway ECU) |
J22-10 (CANH) - J22-21 (CANL) |
Cable disconnected from negative (-) battery terminal |
108 to 132 Ω |
Central gateway ECU (network gateway ECU) |
J22-11 (CANH) - J22-22 (CANL) |
Cable disconnected from negative (-) battery terminal |
200 Ω or higher |
Navigation receiver assembly*1 or Radio and display receiver assembly*2 |
Result |
Proceed to |
---|---|
OK |
A |
NG (Central gateway ECU (network gateway ECU) CAN main line) |
B |
NG (ECU or sensor CAN branch lines) |
C |
A |
REPLACE NO. 6 CAN JUNCTION CONNECTOR |
C |
GO TO STEP 3 |
|
2. |
CHECK FOR SHORT IN CAN BUS LINES (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
(a) Disconnect the N36 central gateway ECU (network gateway ECU) connector.
(b) Measure the resistance according to the value(s) in the table below. Standard Resistance:
|
|
OK |
REPLACE CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU) |
NG |
REPAIR OR REPLACE CAN MAIN BUS LINES OR CONNECTOR (NO. 6 CAN JUNCTION CONNECTOR - CENTRAL GATEWAY ECU (NETWORK GATEWAY ECU)) |
3. |
CHECK FOR SHORT IN CAN BUS LINES (ECU, SENSOR) |
(a) Reconnect the CAN junction connector. |
|
(b) Disconnect the connector that includes terminals CANH and CANL from the ECU or sensor to which the short circuited CAN branch line is connected.
(c) Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection |
Condition |
Specified Condition |
---|---|---|
N36-6 (CA3H) - N36-21 (CA3L) |
Cable disconnected from negative (-) battery terminal |
54 to 69 Ω |
*a |
Component with harness connected (Central Gateway ECU (Network Gateway ECU)) |
HINT:
If the resistance becomes normal (between 54 and 69 Ω) when the connector is disconnected from the ECU or sensor, there may be a short in the ECU or sensor.
OK |
REPLACE ECU OR SENSOR |
NG |
REPAIR OR REPLACE HARNESS OR CONNECTOR |
How To Proceed With Troubleshooting
CAUTION / NOTICE / HINT
HINT:
Use these procedures to troubleshoot the key reminder warning system.
*: Use the Techstream.
PROCEDURE
1.
VEHICLE BROUGHT TO WORKSHOP
NEXT
...
Stereo Component Amplifier Disconnected (B15D3)
DESCRIPTION
The navigation receiver assembly and stereo component amplifier assembly are
connected by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the navigation receiver assembly
and stereo component amplifier assembly, this DTC will be stored.
...
Identification Information
Vehicle Identification And Serial Numbers
VEHICLE IDENTIFICATION AND SERIAL NUMBERS
1. VEHICLE IDENTIFICATION NUMBER
(a) The vehicle identification number is stamped on the vehicle body and on the
certification label, as shown in the illustration.
A:
Vehicle Identification Number
B:
C ...