PROCEDURE
1. |
CHECK USAGE CONDITION |
(a) Check that the vehicle and cellular phone meet the following conditions:
NOTICE:
If changing cellular phone settings, updating software, etc. is necessary, make sure to obtain the permission of the customer before performing it.
(b) Register the cellular phone again and check if it is registered correctly.
HINT:
If operation of the cellular phone or radio and display receiver assembly is requested, make sure to follow the instructions closely and perform the operation.
Result
Result |
Proceed to |
---|---|
Cellular phone can be registered |
A |
Cellular phone cannot be registered |
B |
A |
END |
|
2. |
RESTART CELLULAR PHONE |
(a) Restart the cellular phone.
(b) Turn the ignition switch off.
(c) Turn the ignition switch to ACC.
(d) Register the cellular phone as a connected device again and check if it is registered correctly.
HINT:
If operation of the cellular phone or radio and display receiver assembly is requested, make sure to follow the instructions closely and perform the operation.
Result
Result |
Proceed to |
---|---|
Cellular phone can be registered |
A |
Cellular phone cannot be registered |
B |
A |
END |
|
3. |
BRING CELLULAR PHONE NEAR IN-VEHICLE DEVICE |
(a) Place the cellular phone close to the radio and display receiver assembly.
(b) Register the cellular phone as a connected device again and check if it is registered correctly.
HINT:
If operation of the cellular phone or radio and display receiver assembly is requested, make sure to follow the instructions closely and perform the operation.
Result
Result |
Proceed to |
---|---|
Cellular phone can be registered |
A |
Cellular phone cannot be registered |
B |
A |
END |
|
4. |
CLEAR REGISTERED DEVICE INFORMATION |
(a) Clear all "Bluetooth" devices registered to the radio and display receiver assembly and delete the radio and display receiver assembly information from the cellular phone.
(b) Register the cellular phone as a connected device again and check if it is registered correctly.
HINT:
If operation of the cellular phone or radio and display receiver assembly is requested, make sure to follow the instructions closely and perform the operation.
Result
Result |
Proceed to |
---|---|
Cellular phone can be registered |
A |
Cellular phone cannot be registered |
B |
A |
USE A "Bluetooth" COMPATIBLE CELLULAR PHONE |
|
5. |
CHECK USING ANOTHER VEHICLE |
(a) Check if the cellular phone can be registered normally to another "Bluetooth" compatible vehicle of the same model.
HINT:
Result |
Proceed to |
---|---|
Cellular phone can be registered. |
A |
Cellular phone cannot be registered. |
B |
A |
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
|
6. |
CHECK USING ANOTHER CELLULAR PHONE |
(a) Using another "Bluetooth" compatible cellular phone, register the cellular phone and check that it is registered correctly.
HINT:
Result |
Proceed to |
---|---|
Cellular phone can be registered. |
A |
Cellular phone cannot be registered. |
B |
A |
END (ONLY A "Bluetooth" COMPATIBLE CELLULAR PHONE CAN BE USED) |
B |
REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY |
If your vehicle needs to be towed
If towing is necessary, we recommend having your vehicle towed by your Toyota
dealer or a commercial towing service, using a lift-type truck or a flat bed truck.
Use a safety chain system for all towing, and abide by all state/provincial and
local laws.
The wheels and axle on the ground must b ...
Acceleration Sensor Power Supply Voltage Malfunction (C1381)
DESCRIPTION
The skid control ECU (master cylinder solenoid) receives signals from the yaw
rate and acceleration (airbag sensor assembly) via the CAN communication system.
The airbag sensor assembly has a built-in yaw rate and acceleration sensor and
detects the vehicle's condition using 2 ...
Output Shaft
Components
COMPONENTS
ILLUSTRATION
Disassembly
DISASSEMBLY
PROCEDURE
1. REMOVE FRONT OUTPUT SHAFT BEARING
(a) Temporarily install the manual transmission output shaft rear set
nut to the output shaft.
Text in Illustration
*1
Manual ...