Toyota Tacoma (2015-2018) Service Manual: Brake Switch "A" Signal Compare Failure (P057162)

Toyota Tacoma (2015-2018) Service Manual / Cruise Control / Cruise Control System(for 2gr-fks) / Brake Switch "A" Signal Compare Failure (P057162)

DESCRIPTION

When the brake pedal is depressed, stop light switch assembly sends a signal to the ECM. Upon receiving the signal, the ECM cancels the cruise control system.

DTC Code	DTC Detection Condition	Trouble Area	MIL	Note
P057162	Vehicle Condition: Ignition switch on, cruise control main switch on Malfunction Status: Stop light switch assembly malfunction input signal	Stop light switch assembly Harness or connector ECM	Does not come on	SAE: P0571

WIRING DIAGRAM

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE

1.	CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

(a) Disconnect the stop light switch assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Switch Condition	Specified Condition
S10-2 - Body ground	Always	11 to 14 V
S10-4 - Body ground	Ignition switch on	11 to 14 V
S10-4 - Body ground	Ignition switch off	Below 1 V

Text in Illustration

*a	Front view of wire harness connector (to Stop Light Switch Assembly)

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.	CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH INPUT CIRCUIT)

(a) Disconnect the ECM connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard Voltage:

Tester Connection	Condition	Specified Condition
E13-15 (ST1-) - Body ground	Ignition switch on, brake pedal released	7.5 to 14 V
E13-15 (ST1-) - Body ground	Ignition switch on, brake pedal depressed	Below 1.5 V
E14-10 (STP) - Body ground	Brake pedal released	Below 1.5 V
E14-10 (STP) - Body ground	Brake pedal depressed	7.5 to 14 V

Text in Illustration

*a	Front view of wire harness connector (to ECM)

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.	INSPECT STOP LIGHT SWITCH ASSEMBLY

(a) Inspect the stop light switch assembly (See page INSPECT STOP LIGHT SWITCH ASSEMBLY ).

(b) Clear the DTCs (See page (c) Check for DTCs (See page ). ).

OK:

DTC P057162 is not output

REPLACE STOP LIGHT SWITCH ASSEMBLY

REPLACE ECM

Clutch Switch Circuit

DESCRIPTION Clutch switch circuit inspection is necessary for manual transmission vehicles. When the clutch pedal is released, the ECM receives the positive (+) battery voltage through the ECU-IG ...

Cruise Control Input Processor (P160700)

DESCRIPTION When the ECM determines that there is a malfunction, the ECM illuminates the MIL and stores a DTC. HINT: When these DTCs are stored, the ECM cuts the current supplied to the throttle ...

Other materials:

Diagnostic Trouble Code Chart
DIAGNOSTIC TROUBLE CODE CHART Audio and Visual System DTC Code Detection Item See page B1324 Lost Communication with Meter B1532 LVDS Signal Malfunction (from Extension Module) ...

Pressure Control Solenoid "A" Circuit Open (P074513)
DESCRIPTION Changing from 1st to 6th is performed by the ECM turning shift solenoid valves SL1, SL2, SL3 and SL4 on and off. If an open or short circuit occurs in any of the shift solenoid valves, the ECM controls the remaining normal shift solenoid valves to allow the vehicle to be operated ...

Terminals Of Ecu
TERMINALS OF ECU 1. REAR TELEVISION CAMERA ASSEMBLY (a) Disconnect the T22 television camera assembly connector. (b) Measure the voltage and resistance according to the value(s) in the table below. Terminal No. (Symbol) Wiring Color Terminal Description ...